Batboard

sb

Hi!
Thanks for info. Radio was used in moscad sistem.
I swap it with HLN6412A accessory connector from GM900 and radio is working with that too.
Any chance to get RJ45 pinout ?

sb

Hi!

Inside picture.

sb

Hi!

Need info about FRN 5843A that is attached to mine MCS2000.

sb

Hi!

How can it be done ?

sb

Thanks. CPS R02.03.00 works like a charm

sb

Hi!
I have MCS2000 type1:
MODEL: M01RHL9PW4AN
FLASH CODE: 000001-00000-9
FIRMWARE. R05.58

Which is the correct RSS/CPS for this radio ?

sb

Hi!

I have made this connection for link radio.

Uploaded with ImageShack.us

sb

http://www.batlabs.com/gm350.html

sb

Hi!
Found the manual of Storno CQM5500 which is the the same radio. I have the SELECT 5 radio so it is only one button for channel select.

sb

Hi! I connected GLN1052 from dead McMicro to M110. It is working O.K. but I can change channels in one direction only. All buttons are working except the "house" button. I do not have the manual for GLN1052 so I don´t know if this button is for "CH UP" or not ? http://img513.imag...

sb

Hi! I have GP900-99 whitch is a nice radio but Motorola did a funny thing with channel alias. You can only assign number 0-2 for the first four segments and 0-9 for the last two. So impossible to assign frequency ( like 145500 ) to the channel. I did some hex editing in the .odb file to change 0-2 o...

sb

Hi!

I solved the problem and hoked GM350 to Quantro. COS worked it was mine mistake.

This is how I done the connection.

sb

Hi!

I have quantro set up as analog ham repeater. I want to add link radio. As described on repeater-builder.com I used pins on J17 for PTT and COS. PTT works but COS not.
Any idea ??

sb

Hi!

Does anybody know the duration of TOT on GM600 in conventional mode ?

sb

Hi!

I think MT6000E is radio sold only in UK and in Europe it is known as GP900/99. It is top display 99 ch radio with special MRSS.

sb

Hi!

I have GM350 in the repeater setup. I want to enable TOT , but it can be set to max. 267 sec.
Is it possible to change this time with hex editing ?

sb

Ups

sb

Hi!
Does somebody know where to get pinout for J17 ?

sb

Hi! The quantro was dismantled to parts on the original location and cable was on the way to garbage. Last minute rescue :lol: The rpt will be used in HAM service. I did programm it to RX-431.XXX MHz and TX-439.XXX MHz. TX is out of band but it seams that this is no problem at all. I did test it in ...

sb

Hi!

Problem with PA cable solved. I was lucky to get one

This is the picture of connector on the chasis side. Colours of the wires are the same on the PA connector but orange is not connected!

sb

Hi!

Thank you very much for info!!!
I will try to figure out how to make extension cable for PA (wireing diagram would help ) .
I will need some more help from you guys throught the process of learning Quantro , so have patience with my ignorance and bad english.

sb

Hi! The six pin connector on PA does not match the "37" on frame. http://img227.imageshack.us/img227/4682/quantro007of4.jpg http://img227.imageshack.us/img227/6849/quantro008py8.jpg I pulled out receiver module and I ques that miniUHF connector is the right one !? http://img442.imageshack....

sb

Hi!
Sorry to bother but I need help again . Quantro is realy something new to me and kind of exotic equipement in my area

Where is six pin connector from PA connected ?
And which one is the RX antenna connector ?

sb

Hi!
Problem solved. It turns out that null modem adaptor I was useing was not right.

sb

HI! Well I connected +12V and GND like on my picture and it powers up and goes through self test . I did not connect +5V . Now the problem is I can´t read RPT. When I perform comm test I get " Connected device error;No response from device". I use IBM 486 – 25 MHz laptop and serial cable (...

sb

Hi!

TNX !!!
So this would be the pinout for power supply.

sb

Hi!

I do not have original power supply for Quantro and I want to confirm if this is the right spot to connect +12V ?

sb

Hi!

Yes it was sel5 console.
If I get it runing it will be used for HAM repeater.

sb

Hi! Tnx for info. Pictures of R100 http://img503.imageshack.us/img503/2159/r100024vf7.th.jpg http://img503.imageshack.us/img503/1728/r100025ub7.th.jpg http://img120.imageshack.us/img120/866/r100026jc4.th.jpg http://img72.imageshack.us/img72/3637/r100027kf9.th.jpg http://img515.imageshack.us/img515/9...

sb

Hi!

I have R100 witch was set as base station with MC Centro.
This is firtst one I have and the RSS is a puzzle to me

Where can I see frequency ??
I can only see what is in the picture.
I want to use it as repeater.

sb

Hi!

I have MX2000 for 66-88 MHz and antena is with green colour.
Which frequency split is this colour for ?

sb

Hi!
I thought so

Well another day spent in DOS enviroment

sb

Hi!

Is it possible to dump MT2100 codeplug to MC2100 ?
Both stations will work on the same sistem with 100+ channels and
I don`t want to start from zero with MC2100

sb

Hi!

It is programmed from 145 to 170 MHz same think on any frequency.

sb

Hi!

I have VHF GM900 that I can programm and RX is also O.K.
But when I press PTT it starts to beep continously and green an red LED are flashing. If I push buttons it returns to normal RX.
Any idea ?

sb

Hi! Well I found GM300 when cleaning my shack and try to solve the problem again :D The solution is on this page: http://www.repeater-builder.com/maxtrac/maxtrac-manual-rf-power-control.html But GM300 logic board is different from the MaxTrac logic board :( Is there a foto documented mod for GM300 ??

sb

http://www.oppermann-telekom.de/ht800-modelle.html

sb

Hi!

For GP/GM900/Euro Visar you need realy slow PC , somethink like 286/20.
If you can`t programm all 16 channels you must delite some other functions in the radio ( selective calling etc. ).

sb

Hi!

Can somebody tell me if GM340 has COR,PTT etc. on the acc connector ?

sb

Hi! Here are some pictures of Motorola HKN9755A Cloner/Programming assy. http://img72.exs.cx/img72/7038/DSC749.th.jpg http://img72.exs.cx/img72/9518/DSC745.th.jpg http://img72.exs.cx/img72/9859/DSC744.th.jpg http://img72.exs.cx/img72/2071/DSC742.th.jpg http://img72.exs.cx/img72/7324/DSC741.th.jpg ht...

sb

Hi all.
I have a VHF gm300 programmed on 145 MHz. Power is set to 15W and currently drawing is 2x biger then on 170 MHz/15W.
I understand if radio is hacked out of band that there is no provisions for
soft pot alighnment .
How to solve this problem ?

sb

Hi!

Programmed mine M110 with "noname" 486/33 laptop.

sb

Hi! TNX :D I understand now how it works. The idea is to activate channel steering on the LB GM350 connected bidirectional with UHF GM350 in remote ( mountain top ) location. The UHF radio will be used as link. I must built DTMF controler with MT8870D so I can steer channels on LB radio through UHF ...

sb

Hi!

Can anyone tell me how to use channel steering on GM350 ?

sb

Hi !

Try this:

http://hamradio.online.ru/ftp/dw.php?sch_gm350.zip
http://hamradio.online.ru/ftp/dw.php?pcb_gm350.zip

sb

Geffer, I took a quick look at my old GM900 Repeater Setup, and this is what I found : Across all Mobius platform, I use Pin 7 for the PTT and Pin 8 for the SQL - Ping 8 behavior can be set using the GM900 Rss. I usually set it to follow squelch open - That way, you need a valid PL/DPL and Rf level...

sb

Hi!

I have GM900 with same model number so much the same radio.
It is conventional 16 CH with 5tone signaling.

sb

Hi! Here are some pictures of Motorola HKN9755A Cloner/Programming assy. http://img72.exs.cx/img72/7038/DSC749.th.jpg http://img72.exs.cx/img72/9518/DSC745.th.jpg http://img72.exs.cx/img72/9859/DSC744.th.jpg http://img72.exs.cx/img72/2071/DSC742.th.jpg http://img72.exs.cx/img72/7324/DSC741.th.jpg ht...

sb

Hi!

You need RIB for this one

sb

Hi!

Motorola DTMF mike does not have the a,b,c,d that you may need for HAM aplications.

Search found 87 matches

Re: FRN 5843A

Re: FRN 5843A

FRN 5843A

MCS2000 typeI 48 to 150 channels ?

Re: MCS2000 programming

MCS2000 programming

Re: Quantro interfacing

Re: GM950 no sound

Re: HHCM GLN1052 from McMicro to M110

HHCM GLN1052 from McMicro to M110

GP900-99 ( MT6000E ) display hack

Re: quantro cos

quantro cos

GM600 TOT in conventional mode

Re: what radio is a MT6000?

GM350 TOT

Re: Quantro connectors pinout

Quantro connectors pinout

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Re: Quantro power supply connection ?

Quantro power supply connection ?

R100

MX2000 antenna ?

MT2100 codeplug to MC2100 ?

GM900 acting crazy

GM340 for repeater ??

GM300 VHF high current draw (out of band)

GM350 channel steering