Batboard

stangmansvo

FORGOT !!!!
No plastic bags ideas GUYS
steve

stangmansvo

Well guess this question hasnt been answered many times ; anyways I have a new Steel Rescue Boat for radio & antenna install and looking for any help or suggestions ! specifiy - waterproof or resistant speakers. Seems they dont want to use the siren speaker and like to have an external radio spe...

stangmansvo

well my O' my !

Just got my "NEW" Minitor V program disk today (for free)

Im surprised !!!!
steve

stangmansvo

hey all,
I got an old siren amp and looking for any info (wiring) on a ws295 siren amp.
thanks
steve

stangmansvo

Hi all,
Dont hate me on this post !!!
I need a pinout or info on connecting an external speaker to a tk760 radio. The local FD has one and wanted to use a different speaker.
thanks
steve

stangmansvo

Well now I hope they send me all the programming stuff to program the V's or will I have to buy the new programmer & programs ????
Already paid the $400 for the minitor III & IV programming equipment & software !!!
I beat not

steve

stangmansvo

thanks guys
I always get excellant answers here.
steve

stangmansvo

Hello all
Im looking for info on connecting DC power cable to my tk730
which pin is hot & which is negative????
thanks
steve

stangmansvo

thanks
I replaced the speaker last night and still doesnt work so I will try what you advised.
steve

stangmansvo

Let me clarify my last post :
I have sound thru the ear phone but not the pager speaker.
steve

stangmansvo

Well I connected a ear plug and I have power on tone & light. Still no speaker sound??? Bad speaker maybe ????
Help ASAP

steve

stangmansvo

Hello,
I know this is an off the wall (Motorola) question but since this forum has so many qualified techs I thought I might get some help with identifying this radio VHF or UHF and any info on it .

TACTEC mobile : Model MMAG4A

Thanks
steve

stangmansvo

Hi Bernie

Thanks for responding to my question,
I purchased this monitor used and this problem has been on going since.

thanks Again
steve

stangmansvo

Starting to have problems with my service monitor specifically the oven lamp going out after 10 or so minutes.
The other question is : In the FM monitor stage shouldnt I be able to use this as a standard receiver? if so whats the sittings
steve

stangmansvo

Hello
Im looking for info on swapping a low band Mitrek (in a base station) to High Band VHF 155mhz. I have the radio and my question is :
Can I just swap radios into the Base Station unit and plug & Play?
steve

stangmansvo

Well I finally got the radios programmed.
seems M100 works on these radios but m208 does not.
Go figure !!

steve

thanks all for your help

stangmansvo

Yeah the radios work OK! error code 56
Thanks
I will double check things
steve

stangmansvo

yeah ! Seems crazy to me also
Im using radmbl and both are bad
steve

stangmansvo

Hello everyone,
Im looking for a good codeplug for a M208 (6ch) and M216 (16ch) radius mobile radios. Both of my radios wont program for some unknown reason.
Must be D51 model and one 6ch the other 16ch
thanks
steve

stangmansvo

Hey guys,
I have a 6 ch radius m206 33-36 mhz range with a back codeplug (error 56 read) and liked to know if you might be able to share a good codeplug for this radio ??
steve

stangmansvo

Hello all,
Im looking for info on adding a earphone jack to a kenwood tk278 mic. I dont have any info and need some help.
thanks everyone
steve

stangmansvo

Thanks guys,
Everything you all said worked. This is my first Kenwood installation (Dual Heads) and the Rescue Squad didnt have any information on the radio.

thanks again
steve

stangmansvo

Need assistance with programming a tk730 mobile. I cant get the radio to read or write. Im using a KPG-7D software & KPG-4 cable under DOS. Is there a special trick to program these radios???

HELP ASAP : I have a medic unit in my driveway that needs to go out on MONDAY !!!!!!!!!!

steve

stangmansvo

Seems the local Medic unit wants one control head in the front console and the other control near the rear door for patient care !

Anyways yesterday I put them where they wanted .

steve

stangmansvo

stangmansvo

My mistake I should have looked at the radio alittle more :
Its a TK 730(G) VHF

This would be stickly A VHF radio ? it has dual heads but the radio has only one antenna connection. It kinda fooled me !

steve

stangmansvo

Hi all, Looking for some help on installing a Kenwood tk-690 dual head !! my first question is : does anyone know the pinout connection for connecting ext speakers ??? on the radio head I see one antenna connection on the rear of the radio but I have two different frequency antenni to install ???? g...

stangmansvo

Everyone here has their view about Motorola including myself (which so far I can rate above average!). Im sure radios & pagers (in general) were never ment to be liquid resistant anyways but if you think about it alittle Most firefighters wear them in hazardous conditions including the use of wa...

stangmansvo

Thanks Chuck seems a couple of the Firefighters broke the rear belt clip from the case and I was trying to fine a cheap fix but sounds like a Motorola Flat rate charge. steve :o I sent Deep Creek VFD back at you a couple of months ago for ten Minitor IVs thanks for helping them out !!!! They asked m...

stangmansvo

hi again,
Im looking for the part numbers for Minitor IV pager case both the front & back units.

Thanks Steve

stangmansvo

I loaded my m3 into hexeditor but not sure about all the #s and letters and I dont see any frequency numbers to change.

anyone willing to walk me thru this ??????
im trying to change a minitor III 37-40 down to 33mhz

thanks
steve

stangmansvo

Thanks for the info
wow the first portable that I've owned "Motorola" that didn't beep.
cool
steve

stangmansvo

Hi all,
Im new to Saber III radios and wanted to know should i get a power up alert tone like other motorola portables ????

I didn't see anything in RSS for changing it but I may have missed it.

thanks
steve

stangmansvo

thanks for the info

I haven't played with hexworkshop much but im game.
any additional tips ?
steve

stangmansvo

Hi all,
Im interested in programming some minitor III VHF pagers that are 159-167 mhz down to 158.775 mhz.
Like to know if anyone has any luck doing this ???
thanks
steve

stangmansvo

Well hmmmmmm I sent three Minitor IIs for refurb to Big M about two months ago and cost me $78 each "Where did you get you pagers refurbed"?
steve

stangmansvo

About a month ago Big M was still selling parts for Minitor II pagers
doors $11 and cases $40
Kinda High "I think" but if you want new Oh Well !!!

steve

stangmansvo

Thanks Tom seems the mic connection fits my HT1000 (has small pin in middle) yet the antenna connection on my Saber III doesnt have the pin. So im using a mt1000 antenna right now (works) but Im going to need a antenna adapter from MT1000 to HT1000 antenna to work with the hand mic. thanks again ste...

stangmansvo

Hello,
I received a saber III VHF radio and wanted to know which series antenna works of them. I purchased a hand mic (NMN6217B) and it doesnt screw into the radio antenna connection. Apparently the mt1000 antenna screws in fine but not the hand mic connection.
thanks
steve

stangmansvo

Hi everyone !
Well Im finally getting up to date and purchased my FIRST Saber radio.
Its VHF model : H43SAK7139CN and wondering if anyone had information
on which battery is best for this radio?

Also, I need a new or mint VHF antenna for this radio (155mhz range)

thanks
steve

stangmansvo

This vehicle has two batteries and I guess my question includes ; Is there any concerns drilling in the floor Hump for the radio console (like vents or extra wiring harness??? I have completed a Dodge Durango & several Ford P71 (CVs) but this is my first diesel vehicle . thanks for your time steve

stangmansvo

Hello,
Im involved with installing two mobile CDM radios and like to know whats the experts say??? Electrical connections, and recommendations on mounting hardware????
Need Help
steve
swendling@iceweb.net

stangmansvo

I will keep in touch on this project.
Im fairly new to the hex edit stuff and would like someone who is alot more knowledgable than me.
thanks
steve

stangmansvo

thanks Todd
Sounds like alittle more than I want to tangle with.
Steve

stangmansvo

Hello everyone
Im interested in the possibility of expanding a 4ch HT750 to a 16ch.
Anyone got any ideas on this ? is it possible?
thanks
steve

stangmansvo

thanks Frank
I will let you know then
steve

stangmansvo

MMMMMMMM well now . I wonder if they might still work on the 150-160mhz band? for the price of $50 plus shipping its hard not to take a chance on these.
steve

stangmansvo

The radio is UK type approved ????

whats that mean ?
steve

stangmansvo

thanks Frank
I couldnt find much on them. Are they usually a ten channel radio.
steve

stangmansvo

My local VFD is looking for some cheap VHF portables and I found some tk230s for sale. My question (since these are older portables) is:
anyone have any info on them? I need to be able to program in the 155-159mhz range and like to know if these will work?

thanks
steve
swendling@iceweb.net

Search found 110 matches