I have trouble programming this radio because it uses version 6 in codeplug.. I have V7 and 8 but not 6. You can't downgrade the codeplug so I am looking for a codeplug for a gp366R in version 6.. The radio model is MDH38RDF9AN5AER For now the radio(s) is password protected, so I can't just read the...

Thank you for the reply :-) I need the to send continuously (at low power) Because the radio is going into a OB van, and we need the people on the floor/stage to hear the producer at all times. I know some of the radioes is being used for this purpose, but I can't remember the model number. And the ...

Do you now can the gm 900 do it then ?

Hi, i want to get my gm1200 to transmit alle the time when it is on, without someone pressing the ptt.
I think I can do it in the accessory connector ? but I can't get it to work by shorting ext ptt2 to ground. Anyone know what I am doing wrong here ?

Regards Jens

Hi i have a repeater tha consists of 2 gm 900. The tx unit is only putting 15 watts out on a dummy load. (10 after filter) As far as I know the gm900´s are all 25 watts out? Or am I wrong here? I can't find a breakdown chart at batlabs that is correct for the model, and I can't see it in the rss. Ca...

HI
I am about to program my gp380´s with pl tones.
But when I do, I can hear the tone when I receive, how is it possible to "hide" the tone so I don't actuality hear it?

Kind regards Jens

I have an mc2100 I have tryied to force its own serial number and model number in to it via wookie. At first i could not read it right, and it couldt not see what model it was. After i forced the serial number and modelnumber into it, i could read it and program it, in wookie and rss 02.09.00 But wh...

I have got hold of two mc2100 they both displayes entrep sek 522 when they power up.
Wookie have trouble Reading them.
What does it man ?
Regard Jens

I have 4 that runs 4.x codeplug and two that runs 6.x
In all the 4.x i can here the tone but not in any of the 6.x

/Jens

Yes i know.
But why does the version 4.x not apply the hi pass ? and the 6.x does?
Can it be swiched off somewhere?

/Jens

I can hear the pl tones when i recieve on my gp388 and 380. When the radio starts to recieve it goes =BOING= and then almost disaperes... It waries from what pl tone i use, so it can only be that. It only happens on my version 4 codeplug radioes, not on the version 6. Maybe it is somthing here? Or m...

Hi there. I have an ht1000, that i would like to program the sidebuttons on. it is an AN model, the first ones, so i know that it maybe not posible. I need it to do a 1750 burst tone. It dosent mater what button that does it. As long as it is not the toggleswitch, that is in use. Can it be done? i a...

My swr on my motorolas is allwayes good on alle frequencys. Also if i take the antenne off. It changes a lille when i take the antenna off... When i do the same messuring on my yaesu ft 7800 the swr is not the same on different frequencys. I use the same meter and same antenna/cable. Does the motoro...

I have Found put why.
The link betjene pin 4 and 9 was missing at the 25 pin connector, then it goes into emergency mode by itself
Kind regards Jens

How do i turn the Emergency mode OFF in the radio? It transmittes by it Self, and i Can not change Channel on the radio.
It is the emergency mode it is in. But i cant find the place to disable it in the software.
I use r06.03.00
Can anybody help here?
Kind regards Jens

Normally i just hold the button in til it goes in conventional mode. If you just Press it short, i Think it just toggles betjene the trunked personalityes.
Kind regards Jens

Anybody?

Hi there.
My m2100 has very low modulation.
I am usling an original hmn 1056D mic
Can i sommeren in The rss change The mic gain?
I cant seem to see what rss it is. But it is from dos.

Kind regards Jens

Flash code is 000008-000000-2
Signaling type is none. And i cant choose anything else under here.
So i guess that i wont let me do The 1750 tone then.
Kind regards Jens

Hi.
I have The mts2000.
How do i program one of The Buttons to be a 1750 burst tone?
I cant find it in The cps (r02.03.00) running win xp
kind regards Jens

Hi there. I have allmost build the RLN4008B But i have some questions before i turn it on. I asume that the power in is from 10-30 volts, the first it hits is the regulator...? What does the battery do? is it just so the rib dont need power from the outside? or does it have some backup memmory? i ca...

Think you for reply. :-) In The gm 1200 i Can select high and low power for each Channel in The conventional mode. Them are only gonna transmit within 1 mhz so i thougt That maybe it Would be Wise to only set The Twofrequencys that covers that area to max, or what ever is good for The radio. I have ...

Does anybody know hvad The values from 0-127 stands for in watts in The cps for The gm1200? Say i only want to transmit from 446-447 mhz The it should be ok to only put The values for 438.01250 and 449.01250 to 127? Then it wont be able to transmit on otter frequencys, but kan use All The power on o...

Hi there. I have some motorola gm 1200 That i wantto be able to program in dos by an rss. I have mannager to get to them an program via my old 486 and a cps. Thats All great. But i also want to use The rss in dos on a laptop. I have The 03.03.00 rss but it sayes that it does not support the codeplug...

Ok i Got it to work! The dos rss r0303 does not support The codeplug for this radio. The dps 00.01.10 runs great in win 3.11 My Main problem was port problems. The computer has locked port 1 to the mouse, so i only could use port 2. Port 2 on this old Machine is 25 pin... So i did som soldering and ...

Does it run in win 3.11? Or is it only win 95?
I have 3.11 on my 486 desktop:-)

Can it run under win 3.11?

Hi there. I have a gm 1200 that is in conventional mode. thats fine thats what i want. someone has programed it to this when i bought it. Now i want to change frequency ant squelch settings. etc... I can´t get in contact with the radio. I have the rss r0303, it can only start when i am using the mpt...