Batboard

Vercomm

does this help?

http://www.batlabs.com/images/cdn6351.gif

Vercomm

Running in straight analogue, no digital channels

Vercomm

Hi all,

I have a XPR2500 that will not power on.....cannot power on with power button or by applying 12v to pin 10 of acc. I've open the radio and tried apply 12v the point labelled ignsns, but still can't get it to come on. Any ideas?

Vercomm

There is a firmware update for your repeater...but not sure that is the issue. Are you connecting to cor on system connector j5 c02?

Vercomm

In the station programming, what is you're analogue rx activation set to? Csq or csq/pl?

What station firmware does your unit have?

Vercomm

To high vswr, I've just put 6 of these into service and if the tx is seeing to much reflected they shut down as you have experienced. Bad Antenna, line, connector, filter....one of those (even filter out of tune).

Vercomm

Hey GUys, I've got a MSF5000 403-435MHz repeater station, wondering if anyone has had success in using this type of station in the 445-450MHz range. I'm trying to help out a local HAM club and wondered if the VCO's will go that far, if not is there a mod, or does a person find new VCO's and such to ...

Vercomm

I think the part number you are after is JMLN4638A

Vercomm

Found a manual for the RLN4008D (6880309H26), still looking for the E version.

Thanks!!

Vercomm

Does anybody know if they make a replacement manual for the new E version RIB boxes. Can't order this 6880309C92 anymore.

Thanks!!

Vercomm

Yup those ones......I'll take a look at those schematics and order some parts.

Vercomm

Hi All,

Just wondering if the Motorola RIB boxes are repairable or if they are throw away. I've got a couple that no longer read radios. Was there a common problem with these things??

Thanks!!

Jamie

Vercomm

yes, other frequencies same result.......copied a different codeplug just in case this one was corrupt.....all same result.

Vercomm

as an added note, when i go into the service menu of the radio with rss(specifically tx freq warp) the radio behaves normally when not transmitting. The green light is on and the receiver is happy. The frequency error is adjusted to -10Hz.

Vercomm

Hey Guys, Working on an sm50 VHF that has an open squelch problem. The radio is programmed with TPL in Tx and Rx. The Rx light blinks constantly and if the radio mic is removed from mic clip there is constant noise from the speaker (as if in permanent monitor mode). The radio receives fines and when...

Vercomm

crap, wrong area....not paying attention

Vercomm

Hey Guys, Working on an sm50 VHF that has an open squelch problem. The radio is programmed with TPL in Tx and Rx. The Rx light blinks constantly and if the radio mic is removed from mic clip there is constant noise from the speaker (as if in permanent monitor mode). The radio receives fines and when...

Vercomm

Hi Martin, The Quantar is a very complex beast that can do most anything. I have done quite a bit with Quantars over the years with wildcard tables etc and they are very flexible. I'll see if i can find a soft copy of my wild card programming manual. XMO is also a guru with the Quantar, he may be ab...

Vercomm

thanks a ton!!!!!!

Vercomm

FIRMWARE Problem with that release, you need to upgrade firmware. See below release notes: IMPRES battery capacity – the incorrect capacity readout of fully charged batteries, which was reported with firmware versions R02.06.20 and R01.11.20, was corrected in firmware R02.06.21 (XPR3300, XPR3500, XP...

Vercomm

the files that bring radios up to 1.06.20 are for repeaters only....if you had an old xpr8300 with very old firmware you would have to bring it up to version 1.06.20 first then you could upgrade to the latest firmware. As far as i know with protables and mobiles there are no restrictions like that. ...

Vercomm

Hey All, I'm wondering if anybody knows how to build a USB programming cable for an r750+? If memory serves the original programming cables for the r750 were NKN6522B and were serial on the computer side. Or if someone knows were i can buy a couple. Any help would be much appreciated. Thanks Jamie

Vercomm

Hi Guys,

Couple Questions.

First is the TDN8301B a tone or DC panel? And does anybody have a manual for it?

Thanks!!

Jamie

Vercomm

Really, i don't ever recall seeing one. What part number do you order when you want to get a new flex that includes that piece?

Thanks!!

Vercomm

Hey Guys, I'm having trouble find a part number for a Waris series HT. I'm looking for the adhesive piece that is used to hold the accessory connector to the housing. http://imageshack.us/photo/my-images/214/warispart.jpg/ http://img214.imageshack.us/img214/968/warispart.jpg To explain further the a...

Vercomm

Does anybody know what the actual fix is for this problem, without sending the unit in for repair?

Thanks!!

Vercomm

Hey Guys, Here's what I'm trying to do. Maybe i'm going about it all wrong. I've got several SV Minitor 5 pagers, just single channel, and i want to have them operate just like a NSV. Ideally i'd like them to be in monitor mode and be able to hear everything on their channel. I tried changing them i...

Vercomm

Hi Guys,

I was wondering if you can go the other way. SV to NSV?

Thanks

Vercomm

Hey Guys,

Just wondering if anyone knows of a supplier that sells a headset for a Motorola Mobile (GM300/SM50). I'm hoping for a headset that i can just plug into the front mic port or wire in to the 16pin on the radio without an interface box.

Vercomm

Hey guys, So as the subject says I am connecting an external device to a mototrbo mobile radio. I am wondering about the alignment procedure. I have done tons with analogue stuff, but this will be my first digital. My questions are as follows: I have a GD R8000 test set with mototrbo loaded on it Wh...

Vercomm

Thanks Allen!!

I ordered the parts today!

Vercomm

If I understand the help topic it list DTMF as a supported call alert, but maybe its not supported for the external alarm function.

Just wondering if anybody knows for sure.

Thanks

Vercomm

Hey All, Have a question regarding a CDM1250. I am setting up the external alarm (pin 4 on the rear of the radio). So far i can get the radio to set the alarm out from pin 4 using QCII, but i was really hoping to be able to do this with DTMF. Like i said, it works exactly the way i want using QCII, ...

Vercomm

Hey Guys, I have a Minitor III/3 VHF, NSV, 1 ch pager (A,B,C,D knob) that has a major issue. When you power it on it makes a continuous tone like you have entered the programming mode. It doesn't matter what position i power on the pager etc same result. Just wondering if anyone has seen this proble...

Vercomm

Hey Gang, I have encountered a strange issue with an XPR4550. We are running the radio in analogue only and the unit does have the newest firmware 1.6.20. We have a device sending audio into the xpr through the rear 26pin connector. The audio is voice band and also paging tones. This is the scenario...

Vercomm

i have noticed that when the on/off switch is off the voltage measured on the battery terminals is 7.5v(from my power supply). when i switch the radio on, the voltage across the terminals drops to 1.5v.

Vercomm

Hey Guys, Working on another HT1000, unit will not power up. Fuse and switch are both good. I swapped the controller with a good known unit, no change. I put the original controller back i and swapped the RF board for a good known one and i get a good power up tone. I started digging in the manual (...

Vercomm

I threw the radio in the freezer over night and powered it on. It has now exceeded 30mins of normal operation.

Vercomm

thanks todd, i won't get a chance to get this radio back on the bench until next week. i will let you know what i find out about the heat/cold tests

Thanks!

Vercomm

Hey Guys, Have the following issue with an HT1000. When i turn it on, i receive proper power up tone and radio tx's and rx's perfect. But after being powered on for approx. 10mins the radio emits a tones just like its on a wrong channel. After that, no tx or rx. This happens if you are using the rad...

Vercomm

Hey Guys,

Just wondering if anyone has a manual for the Telephone interface Module (N1385) for the Motorola people finder. The part number of the manual is 6881100B90.

I am trying to find out if the telephone line can stay connected for longer than 30secs.

Thanks!

Vercomm

Does anybody know where to buy/download visio stencils of specific motorola radios (i.e cdm's. maxtracs, xpr's, etc).

Thanks!

Vercomm

Yes....i have the small service instruction booklet.......can email or you can download.

68P81109C65-O

Jamie

Vercomm

First year going....look forward to meeting up with any batlabbers! "The man" is finally forking over the cash for me to go, lol!

Vercomm

Forgot to ask 1 thing, could this speaker be connected to a CDM series radios and the audio input of the speaker connected to Pin 11 of the CDM's acc. connector too?

Thanks!!

Vercomm

Hey Guys, Pretty basic question, but just want to verify. I am connecting an HSN4035 amplified speaker to a MCS2000. I am not using a dual head setup, just connecting the speaker into the MCS' accessory connector. Going to be connecting a remote speaker and mic in a fire truck, but no budget for dua...

Vercomm

Hey Guys, I was wondering if a cdm1250 is able to change the state of one of the pins on the acc. connector when it receives a proper QCII. Have one situation where a fire fighter would like his horn to sound when a valid QCII is received. Automatic reset would be a real bonus for this too. Another ...

Vercomm

Thanks Jacye,

I thought they had button available for things like "siren", "wail", "yelp". I'm gonna be connecting a DEK-Plus to an MCS2000 and I want to have everything on the control for the user.

Do they still make these or did they ever.

Vercomm

Hey Guys,

I'm looking for some MCS2000 replacement buttons...I remember there being a post on here somewhere with part numbers. Anyone remember what it was called, i couldn't find it using the search feature.

Thanks,

Jamie

Vercomm

Awesome instructions Tom!! It was a broken wire from the PTT to the board. I resoldered and its working 100% again.

Thanks for all the tips and insight!!

Search found 311 matches