Batboard

Hey Nurse

This is a rebanded system and rebanding IS enabled via the check box in the codeplug.

Hey Nurse

It's an XTS3000. Oopsy.

Hey Nurse

Hey all, I'm doing a little overtime work on the long weekend and have run into a problem I have never seen before, and that I can't locate any information on here. I have the above noted radio programmed up for a local trunked system ; The radio properly recieves on all the talkgroups it needs to, ...

Hey Nurse

I am not sure....

Hey Nurse

I happen to have another front panel board ((FRN5353B) around somehow. Replacing said board seemed to have cured the TX @ power on problem, but only for a while. If I leave the board connected OR key the mic/front panel TX button, it keeps transmitting until the TOT kicks on OR i kill the power. Odd...

Hey Nurse

Ok...... Finally got some time to play around with this thing again. --The radio transmits fine with a standard control head plugged in. --The transmit radio is indeed on the left side, and appears to transmit just fine with a mic attached to the standard control head. --The "FSOFT" and &q...

Hey Nurse

After some quick testing.....
--Transmits w/o 16pin connector (cable) connected
--Stops transmitting when control panel cable removed.

No time for more; busy day; stupid work.

Hey Nurse

Hey all, got my hands on a desktrac repeater (L35SUM7000BT) for some use on the ranch. On power it transmits constantly, and only stops when the time out timer kicks the transmitter off. I cant see any evidence of damage, though the seller noted that it had been recently changed from 12V dc only ope...

Hey Nurse

If anyone has an srec or codeplug, i'd love them forever!

The radio in question is an XTS3K, M2 in 800mhz flavor. The model # is H09UCF9PW7BN and the flash is 000008-002000-8. The DSP and Firmware is both shown as UNKNOWN in CPS.

Hey Nurse

Well, &^%@#. I'll try a new Srec and if that does nothing, a new controller.

Hey Nurse

Hey all, I have an odd problem here. I was programming an XTS3K for a friend last night. He'd left said radio in the car for a bit, and it was cold. It had a dead(ish) battery, and went through self test VERY slowly, though a fresh battery seemed to help with that. This evening (and with another col...

Hey Nurse

The reason I ask that is because I can put an 80 site smartzone system in with 1 trunking personality. Then I have each the TG's I want in the zone/modes that I want. I am trying to figure out why you need 50+ trunking personalities. F*%k, Im a n00b. I think I figured out how to do it as you were g...

Hey Nurse

Check your PMs.

Hey Nurse

I dont plan on using ALL 255 personalities and I dont plan on having all 16 slots in each zone filled either. 60 (ish) personalities assigned over 5 or so zones would be nice, especially if the radio is capable of 255. 50 does sound fair, but if CPS is saying that the radio is capable of more, that ...

Hey Nurse

Ok, I might be dumb.

Correct me if I am wrong (I usually work with conventional stuff) but this is a feature/setting that must be change via a flash or firmware upgrade......right?

Hey Nurse

Hey all, I have an xts3000 mod 2 in front of me, model H09UCF9PW7BN and flash 000008-002000-8 with sys package H38 in it; The DSP and Firmware versions display "Unknown" in CPS. Information in the "Radio Wide" section of CPS stats that the max number of channels (talkgroups) is 2...

Hey Nurse

A HA! Thanks!

Hey Nurse

Hey all. I have an "advanced mobile mic" (HMN4069) that I'd love to use with some ham gear I have (Kenwood TMD700A). I'm attempting to create an adapter from a piece of cat6and am kind of stuck. I have pinouts for both the Mic and the Radio, but not matter what I do, I cant seem to get the...

Hey Nurse

Through a little more tinkering, I have found out that NO DOS based programming will work........but anything windows (IE MTS2000 CPS or Kenwood TK380 CPS) will work just fine... I have tried all of the aforementioned steps, including the cache disable software and removing/reinstalling the COM port...

Hey Nurse

First off, thank you for all the suggestions posted! I tried messing with this a bit more, and after a bit of tinkering per suggestions... * I uninstalled and reinstalled the COM port in device manager. I Rebooted and now the computer starts to read the radio and then throws a "COM PORT EVENT&q...

Hey Nurse

Andreas wrote:Disable the cache and try it again!

Andreas

This model (Dell Latitude CPi) is set so that the cache may NOT be disabled.

Hey Nurse

Hey all, got something I would love some advice/direction on: Recently my RIB stopped working....or maybe it was my laptop. I am not sure which is to blame. I have a chinabay RIB ~AND~ an RLN4008D OEM RIB and a smattering of older handhelds (HT600, MT1000, Saber II, HT1000, and some MTS2000s). I hav...

Hey Nurse

Hey Nurse wrote:I'd have thought that, however every time I key the mic I get the "error" tone....

PROBLEM SOLVED; MODS DELETE PLEASE

Hey Nurse

I'd have thought that, however every time I key the mic I get the "error" tone....

Hey Nurse

Hey all,

I have an MTS2K. Currently it is only flashed H43/H38 (smartzone systems and remote monitor/trace), but needs to be re- or un-flashed to do plain old conventional systems (H35).

Since flash upgrades for the MTS2K's are NLA, Is there any way to make this happen?

Hey Nurse

Hey all, I bought an MCS2K off the fleabay. The prior owner was nice enough to hack off the female portionof the 6 pin molex for the rear head's amplified speaker. I have 3 wires exposed on either side of the "wound": Orange, Green, and Blue. The Orange/Green wires are roughly 14ga, and th...

Hey Nurse

Would either of you have a codeplug for a H01WCF4DB5AN?

Hey Nurse

I think I have this fixed; had a loose ribbon cable after a new front was installed...........thanks for time spent looking though!

Hey Nurse

Hey all....I have an odd problem: I have an MTX9K B5.....when attempting to read with DOS RSS 6.7 , the radio moementarily shuts off, goes through self test, and turns on again. I have charged the battery fully, cleaned the contacts, ensures the pins were lining up correctly, and so forth.... Any id...

Hey Nurse

Got a computer with win XP. That was the issue.

Hey Nurse

Thanks to you both. I have all of the site data entered, as well as the talkgroup ID's...but need to doublecheck the bandwidth. I think that this is where the ussue may be.

Hey Nurse

Is there a step-by-step guide available somewheres? I am having some problems programming an LS trunked system and would LOVE to know what I am doing wrong.....

Hey Nurse

What would an MCS2K (Mod 2) showing a model number of M01HX + 824W get you? The "X" in the 4th position of the model # throws me. Reasearch on the board and on the model specific page yields great detail about the split and other items, but i cannot find anything that would tell me what a ...

Hey Nurse

Got it all working nicely. Thanks for the advice guys/girls!

Hey Nurse

Firmware in the radio = R5.9.13

Hey Nurse

@MT2Kdes: it's generic, but I havent EVER had a problem with that party's products and the cable is BRAND new. @Escomm: It's a DB9 and the seller advises it is RIBless. I am thinking that the CPS is too old or there is a problem with my trying to run this in compatibility mode like Victor Xray spoke...

Hey Nurse

MTS2000des wrote:real Motorola cable or Ebay special?

fleabay, but from a buyer i have used previously, and trust not to sell me total sh!t.

Hey Nurse

Not sure on the FW; Next time I am home (traveling for work right now) and have it, I'll post it.

Hey Nurse

Will do....

I have used Compatability mode to run a number of other CPS programs (ie MTS2K) without a problem though, so this was a last thought... Thanks for the advice!

Hey Nurse

Hey all.... Bought an HT1250LS+ and a RIBless cable... Everytime i try to read my radio, I get the " Couldn't open port, check if device/RIB/ powered on + check Device/RIB/RIB to computer conntections" error. Can anyone provide some guidance on troubleshooting this; I am new to the PRO ser...

Hey Nurse

I knew there was a misunderstanding here somewhere...haha...like on my end. Thanks again for the info guys!

Hey Nurse

Addendum: this is occurring on RX only (to be clear)....when someone else talks or the CW ID comes over...my tx audio is crystal clear.

Hey Nurse

This is on RX only.....not TX. For instance, i key the mic on my local repeater and if the volume is over half way up, my radio squeals like i am standing right next to someone who is transmitting.

Hey Nurse

Hey all.....not 100% sure if this is the right place for this question (mods, move if need be) . Anyway, Im curious as to what would make my mts2k squeal as if someone were standing next to me while i key up. I was trying to talk on a local ham repeater, doing just fine, but if i turn the volume up ...

Hey Nurse

AWESOME! Thank you SO MUCH!

Hey Nurse

I would suggest you slow down, take a deep breath, and do lots of reading before mucking about with tools and procedures you don't understand. You've already bricked one radio, let's try to avoid bricking another... That is the goal. Got my latest copy of CPS to run in compatibility mode.....got a ...

Hey Nurse

I didnt realize that, no......thanks for the warning! I'l monkey around with cps/vista...

Hey Nurse

Anyone have a codeplug for a UHF MTS2000 model II, Model ## H01RDF9PW1BN, Firmware R05.44

Hey Nurse

This Radio has Firmware Version 5.44 in it.

Hey Nurse

Thank you both for the computer info....but I'll leave that for another pay period.
What I am really interested in knowling is the answer to the question regarding whether locating a codeplug that WAS programmed in DOS RSS (ver 6.xx) and then programming that into this radio will brick it or not?

Search found 92 matches