Mods, would you please make this a sticky.
Below is a listing of the special function codes for the R2000D series analyzers.
SPECIAL FUNCTION CONTROL CODES
• The card supplied with the R-2001D and the applique inside the front-panel cover show the special function
codes. Table 3-3 lists the special function control codes grouped according to the first digit of the code
and then grouped by function type.
• A master reset code 0 (zero) causes all function types to revert to the default states listed in table 3-3.
• To obtain a CRT display of all activated special functions, simultaneously depress both keypad cursor
keys twice. The screen will automatically return to standard operation after 10 to 15 seconds.
CODE MODE ACTIVATES
0 Master Reset Clears all special functions (default state)
10 Encode/Decode Clears all 1x special functions (default state)
11 Encode/Decode Baseband
12 Encode/Decode Decode only
13 Encode/Decode Encode Only
20 Monitor Clears all 2X monitor special functions (default state)
21 Monitor Enables 300 Hz LPFL
22 Monitor Enables 3 KHz LPFL
23 Monitor Enables 20 KHz LPFL
24 Monitor Enables 5 Hz HPFL
25 Monitor Enables 300 Hz HPFL
26 Monitor Enables 3 KHz HPFL
30 Frequency Clears all frequency 3X special functions (default state)
31 Frequency Enables direct frequency readout (10 Hz resolution)
32 Frequency Enables direct frequency readout (1 Hz resolution)
33XY Frequency Enables scan lock from XOO MHz to YOO MHz
3300 Frequency Enables full-band scan lock
34XY Frequency Enables scan latch from XOO MHz to YOO MHz
3400 Frequency Enables full-band scan latch
40 Enables automatic DVM ranging (default state)
41 Enables 1.0 V DVM range
42 Enables 10 V DVM range
43 Enables 100V DVM range
44 Enables 300V DVM range
50 Modulation Meter Enables automatic modulation ranging (default state)
51 Modulation Meter Enables 10 KHz range
52 Modulation Meter Enables 100 KHz range
60 Auto counter resolution (default state)
61 Counter 0.1 Hz resolution
62 Counter 1 Hz resolution
63 Counter 10 Hz resolution
64 Counter 100 Hz resolution
65 Counter 1 KHz resolution
70 Sets factory control states (default state)
71 Sets the current state as the power-on state
72 Initiates a system self test
73 Disables the automatic switching to monitor mode if the input signal is over 0.1.W.
74 Mutes speaker during GEN
7700 Resets from duplex to simplex (default state)
77XY Sets the last XY in RF memory presets as duplex
78000 Disables audible alarm (default state)
78XYZ Sets deviation audible alarm to XY.Z KHz
79 Resets nonvolatile memory
89 Resets option memory
99 Shows resident version of system software
- Board index Focused Discussion Test Equipment & RF Equipment Alignment
- Search
-
- It is currently Thu Mar 28, 2024 9:00 am
- All times are UTC-08:00
R2000D series special function codes
This forum exists for the purposes for discussing service monitors (This includes but is not limited to Motorola, HP, Aeroflex, GD, etc). Additional topics allowed include test procedures, interpretation of test results, where to find information about specific tests, antenna VSWR, return loss testing, duplexer and filter alignment, etc.
Moderator: Queue Moderator
Return to “Test Equipment & RF Equipment Alignment”
Jump to
- Administrative
- ↳ Announcements and Forum News
- ↳ Forum Rules
- General
- ↳ General Motorola Solutions & Legacy Radio Discussion
- ↳ Radio Programming
- ↳ Software & Firmware Releases & Issues
- ↳ Codeplug Information
- ↳ NFPA 1802 Discussion
- Current Motorola Solutions Public Safety / Astro Product Line
- ↳ APX NEXT
- ↳ APX Series Subscribers
- ↳ ASTRO Series (Astro Saber, Spectra, XTS3000/3500) Subscribers
- ↳ ASTRO25 Series (XTS/XTL 1500/2500/5000) Subscribers
- ↳ ASTRO Experimental - How to do things a little out of the box
- ↳ ASTRO Products Feature Requests & Future Speculation
- ↳ Legacy Batboard Motorola ASTRO (VSELP/IMBE/AMBE) Equipment Forum
- Current Motorola Solutions Professional / Business Product Lines
- ↳ MotoTRBO ION Devices
- ↳ Motorola CP/CM Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (3xxx/5xxx/7xxx/SL) 2.0 Series Subscribers
- ↳ MotoTRBO Repeaters, Trunking, and Site Infrastructure
- ↳ MotoTRBO 3rd Party Application Discussion & Support
- ↳ MotoTRBO/Business Products Feature Requests & Future Speculation
- ↳ Experimental - How to do things a little out of the box
- Motorola System Infrastructure (Consoles, Base Stations, Repeaters, Trunking, etc.)
- ↳ Smartnet/Smartzone/Project 25 (Phase I/II) Systems
- ↳ Base Stations, Repeaters, General Infrastructure
- ↳ Consoles
- ↳ Experimental - Mods, and how to do things a little out of the box
- ↳ Infrastructure Product Feature Requests & Future Speculation
- Focused Discussion
- ↳ Motorola Digital and Voice Paging
- ↳ Converting Motorola Equipment to 900MHz Amateur
- ↳ Test Equipment & RF Equipment Alignment
- ↳ Vehicle Radio Installs
- ↳ Experimental and Next Generation LMR
- ↳ Motorola Digital Radio Compatability
- Off-Topic Discussion
- ↳ Vehicle Warning Equipment Discussion
- ↳ Computer/Technical Assistance
- ↳ Knowledge Base