Page 1 of 1

MCS2000 Model III Remote Mount Kit Question

Posted: Thu Sep 11, 2014 11:03 am
by n9wys
Good afternoon.

I have a MCS2000 Model III radio and I have obtained the H1635A Remote Mount Kit for it. My question is - how do I enable the remote speaker that plugs into the 2-pin AMP connector on the remote cable? I'm assuming I need to jumper something in the 25-pin accessory connector, but I'm not sure which pins. The remote kit came without documentation.

A diagram I found on the BatLabs page said that Pins 1 and 2 need to be jumpered for the programming cable, but do I need to do that as well to enable this speaker? If not, which ones? There are no wires near the chassis connector which might be speaker leads... Anyway, I tried Pins 1 and 2, and then Pins 2 and 3, but no audio comes out of the speaker in either configuration.

The radio originally came with the desk mount kit (similar to the HLN6045, with a speaker installed) and it was connected to Pins 1 and 3 of the accessory connector... I don't think I want to jumper these, or I'll blow up the audio amplifier. Or have I already done that??? (Gawd, I hope not...)

Thanks in advance!
Mark - N9WYS

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Mon Sep 29, 2014 6:38 am
by tdats
On the plug that came installed in my remote head MCS2000, pins 1 and 2 are jumpered. There is also a jumper from pin 4 to pin 9. If I pull the plug out, the speaker quits working, so I assume one of these jumpers makes it work. It is not a model 3 head though, I think it is a model 2 head.

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Mon Sep 29, 2014 5:56 pm
by N4KVE
Pin 1, & pin 3 go to the speaker. Make sure you do NOT ground either pin. GARY

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Tue Sep 30, 2014 6:09 am
by fineshot1
Mark - if you still need the doc i have one and it is an 11 page doc.
If necessary i can scan each page into PDF's or mail you the original doc.
The Document number i have is 68P81084C29-0. There is no date on it
but i think it is from the 1990"s.

.......Dan N2AYM

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Fri Oct 03, 2014 5:31 pm
by n9wys
Gary,

Yes, Pins 1 and 3 go DIRECTLY to an external speaker, but the remote mounting kit has provisions wired into the cabling for a remote speaker as well, as evidenced by a pigtail with an AMP connector matching that similar to the Spectra remote speaker connection. Initial indications I was getting were that Pins 1 and 2 need to be connected to make this work - I'm trying to make certain of this. I fear that I may have already blown up the audio amplifier during experimentation... <sigh>

Dan,

If you could scan it into a .pdf and e-mail it to me, I'd appreciate it!! I can take up to a 20 MB attachment, and I don't think an 11-page .pdf would go over that limit.

My e-mail is: n9wys <(at)> ameritech <(dot)> net

Thanks!
Mark - N9WYS

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Fri Oct 03, 2014 8:26 pm
by N4KVE
Pins 1 & 2 get connected to activate the internal speaker for a type 1 radio. But since type 2 & 3 radios have no speaker, pins 1 & 3 get connected to the speaker. GARY

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Thu Oct 09, 2014 4:34 am
by fineshot1
n9wys wrote: Dan,

If you could scan it into a .pdf and e-mail it to me, I'd appreciate it!! I can take up to a 20 MB attachment, and I don't think an 11-page .pdf would go over that limit.

My e-mail is: n9wys <(at)> ameritech <(dot)> net

Thanks!
Mark - N9WYS
Mark - I'll get to doing the scan asap but both my work and personal schedules are very busy so
there will be at least several days more of delay.

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Thu Oct 09, 2014 8:39 am
by n9wys
Not a problem, Dan. I understand and appreciate your doing this for me!

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Sun Oct 12, 2014 5:19 am
by fineshot1
n9wys wrote:Not a problem, Dan. I understand and appreciate your doing this for me!
2 Emails sent - let me know if all went well and you received all 11 PDF's(pages 1-11)

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Sun Oct 12, 2014 8:55 am
by n9wys
Replied direct as well...

Got 'em all... MANY THANKS, Dan!!

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Tue Oct 28, 2014 10:02 am
by Dave
Pins 1 and 2 are jumped together inside of the option connector. You then connect an external speaker to the speaker connector on the control cable.

Re: MCS2000 Model III Remote Mount Kit Question

Posted: Tue Oct 28, 2014 11:28 am
by fineshot1
Oops - i forgot to mention to all interested in this thread
that Motorola has a part Number HKN6127A called a
"Renegade Cable Assembly", that is a cable about 10 or
11" long with the 2 pin audio molex connector on one end and
the necessary DB25 Accessory pins on the other end which
makes it real easy to add that to the DB25 Accessory connector
if your model 1 internal speaker is not enough for your liking.
The pins would be mounted in the DB25 Connector in the holes
for pins 1 and 3 and then the connector re-assembled and then
connection to an external speaker is easy.