operating a code synthesizer II ?
Moderator: Queue Moderator
operating a code synthesizer II ?
Does anyone know how to operate one of these? In "Single" mode, it seems to always put out 1000 hz, and if you press a number it pulses that many times. I thought you could enter in a frequency like a PL freq and it would send it. In 2 tone mode, it always seems to send the same 2 tones. Any help appreciated!
Thanks Alan!
I just got one of these a while back off ebay and have been confounded by it also. Now with your help I have the single and two tone figured out.
The one here is a Model R-1151A and I got it mainly to test out the QCII function on the Sabers and the CTCSS/DCS also.
I am not sure how to set the DCS (DPL?) on the R-1151A either since I am without a manual. It seems to use a different output connector as well. Lots of button pushing but nothing showing on the scope for the DPL output. I must be doing something wrong.
Any clues on that?
Also I found nothing in the way of an online manual on this beast on the internet either.
Thanks,
Eddie
N4UMJ
I just got one of these a while back off ebay and have been confounded by it also. Now with your help I have the single and two tone figured out.
The one here is a Model R-1151A and I got it mainly to test out the QCII function on the Sabers and the CTCSS/DCS also.
I am not sure how to set the DCS (DPL?) on the R-1151A either since I am without a manual. It seems to use a different output connector as well. Lots of button pushing but nothing showing on the scope for the DPL output. I must be doing something wrong.
Any clues on that?
Also I found nothing in the way of an online manual on this beast on the internet either.
Thanks,
Eddie
N4UMJ
- Mikey
- Posts: 410
- Joined: Wed Sep 05, 2001 4:00 pm
- What radios do you own?: CDM1550 LS+, HT1250, MCS2000
Code Synthesizer
I too Have a Code Synthesizer II and am looking for an Owners manual. If you run across one let me know if i can get a copy of it from you. Thanks
Mikey
Mikey
Thanks for that Part Number and info Dave.......
I went to the Motorola Site before posting the previous message but was unable to turn anything up on it. Then again I don't have the Motorola Access setup either. Sure miss the old days when I did.
I'm amazed at some of the lower priced manuals with Motorola.
Eddie
N4UMJ
I went to the Motorola Site before posting the previous message but was unable to turn anything up on it. Then again I don't have the Motorola Access setup either. Sure miss the old days when I did.
I'm amazed at some of the lower priced manuals with Motorola.
Eddie
N4UMJ
- Big Blue TO/\/\
- Batboard $upporter
- Posts: 213
- Joined: Fri Aug 30, 2002 12:16 pm
Synth manual
I began a similar thread a while back. I now have 3 manuals, by the luck of the draw. paid for 1, and rcvd 2 from wonderful bat-labers. I can part with 1 via SASE (large manilla, about a buck or so in stamps)
PM me if you need one.
Tom
PM me if you need one.
Tom
KE4RXM
You don't drink beer? Use Motorola RSS, you WILL soon...
PLEASE use EMAIL over PM. Much Easier for Me. Thanx!
You don't drink beer? Use Motorola RSS, you WILL soon...
PLEASE use EMAIL over PM. Much Easier for Me. Thanx!
Re: operating a code synthesizer II ?
Hello,
I'm also looking for the Motorola Code Synthesizer ll manual....or some info on how to program it to test page on 1600 baud 3200 baud and 6400 baud...for flex
I thought it was 7 store 0 0 store 4....1 store 4 and 2 store 4....also....is it 8 store 0 for alpha
any help would be great....Thanks
I'm also looking for the Motorola Code Synthesizer ll manual....or some info on how to program it to test page on 1600 baud 3200 baud and 6400 baud...for flex
I thought it was 7 store 0 0 store 4....1 store 4 and 2 store 4....also....is it 8 store 0 for alpha
any help would be great....Thanks
Re: operating a code synthesizer II ?
Actually, the R1150 manual won't do you any good for testing flex pagers. What you need is the update or addendum for the R1151. Unfortunately, I never used the flex testing procedures. I was out of the test equipment service area doing computer support and administration duties when flex came out so I don't know what the sequence you need is. Perhaps if someone has the manual update, they could scan a copy of the flex programming and e-mail it to you.goblue wrote:Hello,
I'm also looking for the Motorola Code Synthesizer ll manual....or some info on how to program it to test page on 1600 baud 3200 baud and 6400 baud...for flex
I thought it was 7 store 0 0 store 4....1 store 4 and 2 store 4....also....is it 8 store 0 for alpha
any help would be great....Thanks
Dave
Re: operating a code synthesizer II ?
Thanks....
Re: operating a code synthesizer II ?
Are all versions of the Code Syntheiszer II capable of doing Flex or was it a firmware upgrade? How does its feature set and usability compare with the Ramsey PE-6400?
?
?