HT1250 EEPRM CS ERROR

central150 · Post by **central150** » Tue Nov 02, 2004 12:03 pm

I know this error is a checksum error. I did some searching and couldn't find a solid answer if this is something that I could fix or would have to send out to the Depot. I was programming, then got the error beep when the radio powered back up, and was unable to read the codeplug. I was able to write to it, but it would still give the error. help me..

-Tony

ANB_Medic · Post by **ANB_Medic** » Tue Nov 02, 2004 1:26 pm

I had the same problem a while back.

If memory serves, I just loaded a c/p from a good radio and cloned it over.

Give it a shot. If it doesn't work, let me know and I'll pull up my notes.

Todd

central150 · Post by **central150** » Tue Nov 02, 2004 1:28 pm

Tried that already... used the codeplug that I had saved, and it didnt work.

-Tony

ANB_Medic · Post by **ANB_Medic** » Tue Nov 02, 2004 1:31 pm

Yeah, I had that issue as well. You're going to have to find another radio, read the plug and then clone it in to the brick. Don't know why it doesn't take the original, but it won't.

Todd

central150 · Post by **central150** » Tue Nov 02, 2004 3:20 pm

I tried that too...that didnt work either.

ANB_Medic · Post by **ANB_Medic** » Tue Nov 02, 2004 3:51 pm

Hmm... Not sure what to tell you then... It worked for me. See the following post...

http://batboard.batlabs.com/viewtopic.p ... hlight=doh

Sorry I couldn't be of more help.

Todd

ltec123 · Post by **ltec123** » Tue Nov 02, 2004 3:51 pm

Which version software are you using?

I used 6.04 then changed to 6.05 and works fine since...

LT

central150 · Post by **central150** » Tue Nov 02, 2004 3:54 pm

I am using 6.04.... maybe i need upgraded cps

central150 · Post by **central150** » Tue Nov 02, 2004 3:59 pm

or maybe a good codeplug...my model number is AAH25KD9AA6...

Post by **HumHead** » Tue Nov 02, 2004 5:32 pm

Sometimes a firmware upgrade will do the trick as well.

If you can find a radio, of the same model, that is a candidate for a firmware upgrade, you can start the upgrade compatability check with that radio and then switch to the hosed radio for the actual upgrade. (i.e. Switch radios once it tells you to put the radio into bootstrap mode.)

central150 · Post by **central150** » Tue Nov 02, 2004 5:34 pm

I dont believe I have the hardware for that kind of trick. I thought that the radio I used to clone was the same model number but it wasn't. I NEED HELP!! I NEED CODEPLUG!

-Tony

ANB_Medic · Post by **ANB_Medic** » Tue Nov 02, 2004 7:29 pm

What's your full model number and firware version?

T.

central150 · Post by **central150** » Tue Nov 02, 2004 7:37 pm

AAH25KDH9AA6AN firmware version is 2.03

central150 · Post by **central150** » Wed Nov 03, 2004 4:29 pm

I got a good codeplug from the same type of radio, programmed it into mine and I still get the error. This freaking error is killing me.

-Tony

lovemoto · Post by **lovemoto** » Thu Nov 04, 2004 6:03 pm

Hi, I heard replacing the EEPROM will solve this problem for GP328.