I am trying to program an HT 600. When I use the RSS it won't let me change the PL Codes individually. It seems you have to go to "PL-QC II Configuration" settings and it gives you choices of 4 modes to be in. When I change the PL codes in this mode it seems to default all channels into my one selection. The only other radios I have programmed are HT 100s and that RSS lets you do it easily per channel.
Any assistance would be appreciated....
Below is the screen I see:
F1 - Help
F2 - Mode A: 1TPL, 1 DPL, 1 Quick Call II
F3 -
F4 - Mode B: 2 TPL, 2 DPL
F5 -
F6 - Mode C: 3 TPL, 1 DPL
F7 -
F8 - Mode D: 1 TPL, 3 DPL
F9 -
F10 - Exit, Return to Previous Screen
HT 600 Programming Question
Moderator: Queue Moderator
Hi:
When programming the PL / DPL Tones, you
must 1st chose one of the Modes. Once the
mode is selected, it is set ( and that mode
chosen is for all the channels )
That is to say if you chose Mode C, you can chose " Any " three PL Tones and 1 DPL Tone
and that is selected in the Personality at the Bottom on the Window when programming your Frequencies.
At the Bottom of the Screen you can select
CS/PL/DPL, and then you can then chose which
PL or DPL ( Which has been pre-selected by
the Mode selection)
So if you have 3 PL Tones like 1A, 1B, 2B, DPL 311, when in the Porgram Screen, you can
select " Only " one of the above.
Its not really like the later radios where you can select any of the PL or DPL tones for
a particular channel.
If that explanation is not detailed enough, please email me, and I can probably copy the
Page from the RSS Factory Porgraminmg Manuel
Monty
F1 - Help
F2 - Mode A: 1TPL, 1 DPL, 1 Quick Call II
F3 -
F4 - Mode B: 2 TPL, 2 DPL
F5 -
F6 - Mode C: 3 TPL, 1 DPL
F7 -
F8 - Mode D: 1 TPL, 3 DPL
When programming the PL / DPL Tones, you
must 1st chose one of the Modes. Once the
mode is selected, it is set ( and that mode
chosen is for all the channels )
That is to say if you chose Mode C, you can chose " Any " three PL Tones and 1 DPL Tone
and that is selected in the Personality at the Bottom on the Window when programming your Frequencies.
At the Bottom of the Screen you can select
CS/PL/DPL, and then you can then chose which
PL or DPL ( Which has been pre-selected by
the Mode selection)
So if you have 3 PL Tones like 1A, 1B, 2B, DPL 311, when in the Porgram Screen, you can
select " Only " one of the above.
Its not really like the later radios where you can select any of the PL or DPL tones for
a particular channel.
If that explanation is not detailed enough, please email me, and I can probably copy the
Page from the RSS Factory Porgraminmg Manuel
Monty
F1 - Help
F2 - Mode A: 1TPL, 1 DPL, 1 Quick Call II
F3 -
F4 - Mode B: 2 TPL, 2 DPL
F5 -
F6 - Mode C: 3 TPL, 1 DPL
F7 -
F8 - Mode D: 1 TPL, 3 DPL