Motorola Radius M130 COR
Moderator: Queue Moderator
Motorola Radius M130 COR
Hi,
I have a Motorola M130 radio that I would like to use as a receive radio in a GR repeater configuration and the radio does not have COR on pin number 8 on the 16 pin connector. I have tried to use the RSS to program the connector, however, no menu exist for this. I think this radio has a limited logic board and the 16 pin connector is configured from Mototorola. Does any one have any suggestions on how to get a COR signal from the receiver onto the 16 pin connector???????
Thanks!!!!!
I have a Motorola M130 radio that I would like to use as a receive radio in a GR repeater configuration and the radio does not have COR on pin number 8 on the 16 pin connector. I have tried to use the RSS to program the connector, however, no menu exist for this. I think this radio has a limited logic board and the 16 pin connector is configured from Mototorola. Does any one have any suggestions on how to get a COR signal from the receiver onto the 16 pin connector???????
Thanks!!!!!
Bill, WD9CMS
444.775 PL131.8/NAC293
927.900 PL131.9/NAC293
444.775 PL131.8/NAC293
927.900 PL131.9/NAC293
The M120 has the pins that can be programmed to do that. I think the 130 is limmited like the SM50 is.
If not I do make up the cable to bring out a valid receive signal and audio to use with my modules as part of the module cost. The other radio in a repeater used as the transmitter does not need a 16 pin connector as the module plugs into the mic jack.
If not I do make up the cable to bring out a valid receive signal and audio to use with my modules as part of the module cost. The other radio in a repeater used as the transmitter does not need a 16 pin connector as the module plugs into the mic jack.
re: modulated...
Hey, all this talk of modules... Of curiosity, what's the cost?
thanks!
thanks!
•·•·•
Woody
---Please use the EMAIL button, not PM, tnx!---
Woody
---Please use the EMAIL button, not PM, tnx!---
re: tricky ricky
Well, that's downright affordable, ain't it? Thanks for the info!
Mental note: Forget RICK, Remember WILL
and I'll pass it on to a fellow that's looking for a rick.
thanks again,
Mental note: Forget RICK, Remember WILL
and I'll pass it on to a fellow that's looking for a rick.
thanks again,
•·•·•
Woody
---Please use the EMAIL button, not PM, tnx!---
Woody
---Please use the EMAIL button, not PM, tnx!---
Thanks Will for trying to sell a module....but that does not answering my question. I would like to use this radio with a CAT-1000 repeater controller not a Rick or Rick like module. Does anyone on the board know how to get COR out of a M130???????
Thanks,
Thanks,
Bill, WD9CMS
444.775 PL131.8/NAC293
927.900 PL131.9/NAC293
444.775 PL131.8/NAC293
927.900 PL131.9/NAC293
He's already tried that, and the accessory pin menu isn't there. Pin 8 should normally be defaulted to COR in the masked logic boards, but I don't have an M130 in front of me to check out. I have taken COR in the past from one of the pins in the audio PA. I forget which pin number, but one of them goes from ground to approx 1.3 volts during unmuting, if I remember correctly. Use that voltage to trigger a transistor to ground for your COR.
Todd
Todd
-
- was grem467
- Posts: 1145
- Joined: Mon Jul 21, 2003 12:46 pm
Follow this link & read kcbooboo's post regarding wiring in a simple transistor circuit to give a COR output.
http://batboard.batlabs.com/viewtopic.p ... or+%2Am130
Todd
http://batboard.batlabs.com/viewtopic.p ... or+%2Am130
Todd
No trees were harmed in the posting of this message...however an extraordinarily large number of electrons were horribly inconvenienced.
Welcome to the /\/\achine.
Welcome to the /\/\achine.
Yes, this was recently discussed in this thread here:RADIONET wrote:Hey,
To make the M130 work for RX you have to program the radio as a repeater on the RSS.
Change to repeater mode and program the radio.... it WILL work.
http://batboard.batlabs.com/viewtopic.php?t=43861
I believe you were the person I'm referring to who posted about using repeater mode before. Good info.
Todd
No trees were harmed in the posting of this message...however an extraordinarily large number of electrons were horribly inconvenienced.
Welcome to the /\/\achine.
Welcome to the /\/\achine.