XTS2500 Channel Announce Feature

a1emt · Post by **a1emt** » Wed Sep 06, 2006 11:48 am

I am in the process of ordering some 800 MHz XTS2500's. I thought that the Fireground Voice Announcement feature was going to be added to the XTS2500 (like the XTS5000).

Does anyone know what the option code is for this ? I am getting conflicting reports.

Thanks in advance !

Jim

Post by Pj » Wed Sep 06, 2006 2:44 pm

Fireground voice annocement or Channel Annoucement? I never heard of the 1st, but I think the 2nd is becoming standard.

Jason · Post by **Jason** » Wed Sep 06, 2006 2:52 pm

Fireground Accountability Software and Audible Channel Announcement are two different options, Ill see if I can find the option codes for ya.

Post by Pj » Wed Sep 06, 2006 5:05 pm

At least for the 5k (and most likely the 2500)

Q445 ADD: FIREGROUND ACCOUNTABILITY SOFTWARE

I believe someone posted not too long ago that channel annocement was coming standard from the factory, but I am not 100% sure if that is accurate or not.

bellersley · Post by **bellersley** » Wed Sep 06, 2006 6:04 pm

Isn't channel announcement where the radio "affiliates" either via Astro or MDC when the user changes the channel?

Up here, the Toronto Police have a bunch of analog conventional channels in their radios. Whenever they select one of them, it sends out an MDC burst announcing it's presence on the channel.

tvsjr · Post by **tvsjr** » Wed Sep 06, 2006 6:23 pm

Channel Announcement is where the radio plays a special voice file when a channel is selected. You end up with your radio saying "Fire", "Patrol 1", or whatever you record into it (via CPS) to tell you what channel you're on without referring to the display.

a1emt · Post by **a1emt** » Wed Sep 06, 2006 8:44 pm

The Channel Voice announcement is what I am after. I too thought that it was going to be standard on the XTS2500's with the newest firmware, but I can't find any documentation to support it. The sales rep is saying it is only available on the XTS5000.

Jim

RocketNJ · Post by **RocketNJ** » Thu Sep 07, 2006 3:05 am

It is most likely only available on the 5k since the 5k has 8 meg of memory.

Bruce1807 · Post by **Bruce1807** » Thu Sep 07, 2006 3:14 am

It is available on the XTS2250 so I don't see why it's not on the 2500
Should be in the main setup screen

kj7xe · Post by **kj7xe** » Thu Sep 07, 2006 10:45 am

I'm using Channel Announcement on a 2500 right now and it works no different than a 5K;

XTS2500:
Model H46KDF9PW6AN
Flashcode 100001-000000-7

The only feature in the feature set is 'Q811 - P25 Digital Conventional' and nothing else. On the 5K the option is 'Q446 - Channel Announcement'. Channel announcement might be built into this flashcode?

a1emt · Post by **a1emt** » Fri Sep 08, 2006 8:36 am

Ok folks... after discussion with three different people from Schaumberg, I have found out that the 2500 will do Channel Voice Announcement **If ** it is flashed for any of the flavors of P25 Digitial operation. If you do not add any digital options to the flash (analog only radio) then there is no voice announce option.

Thanks for all the replies !

Jim

Post by Pj » Fri Sep 08, 2006 4:41 pm

That would make sense as the DSP in the radio is used to convert the wav file into the msv file.

a1emt · Post by **a1emt** » Sat Sep 09, 2006 8:38 am

Hey PJ.... what does DSP stand for ?

Jim

Post by **alex** » Sat Sep 09, 2006 10:33 am

Digital Signal Processor

Andre · Post by **Andre** » Wed Nov 15, 2006 3:32 pm

I am using CPS R08.00.00, I have a XTS2500 Ver 07.01.01 and I can't seem to activate the channel announcement, the box in the radio wide, general tab is darkened, like you could check it off, but it won't let me. I've got the voice files uploaded and they are showing up. In the zone section the channel annoucement portion is still grey like its not available. but if you click on the drop down it shows you my mvf files that are available. I do have Astro Digital operation, not sure if my firmware is not quite new enough???

Andre · Post by **Andre** » Wed Nov 15, 2006 4:12 pm

DISREGARD I closed the CP and re-read the radio, and it then allowed me to do what I wanted!!! And boy is it pretty neat!!
Thanks

oh2lna · Post by **oh2lna** » Fri Mar 07, 2008 2:59 pm

Pj wrote:That would make sense as the DSP in the radio is used to convert the wav file into the msv file.

Do the wav files need to be in any specific compressed wav format, bitrate or bit depths? How does a 4-Meg XTS2500 limit those file lengths in practice?

MotoFAN · Post by **MotoFAN** » Sun Mar 16, 2008 5:49 am

oh2lna wrote:
Pj wrote:That would make sense as the DSP in the radio is used to convert the wav file into the msv file.
Do the wav files need to be in any specific compressed wav format, bitrate or bit depths? How does a 4-Meg XTS2500 limit those file lengths in practice?

Yes - juat check the CPS help for e.g. for WAV keystroke.

Up to 3 secs in practice.

XTS2500 Channel Announce Feature

XTS2500 Channel Announce Feature

2500

Re: XTS2500 Channel Announce Feature

Re: XTS2500 Channel Announce Feature