Renting a tower for GMRS Repeater...
Moderator: Queue Moderator
Renting a tower for GMRS Repeater...
Hi Everyone,
I am looking for some information about renting tower space for a GMRS repeater. I currently have a GR1225 repeater connected to a 6.6 DB gain antenna. The problem is the system does not work very well. I cannot talk to the repeater outside of 1 - 2 mile radius unless I am on top of another hill. This apparently is due to location as we are surrounded by several hills, and also the elevation of the antenna is not very high. I have it about 25 feet in the air but I do not believe that is enough. My question is how I go about finding information about renting tower space on someone else’s tower. Any information or assistance is greatly appreciated! Thank you!
-Bob
I am looking for some information about renting tower space for a GMRS repeater. I currently have a GR1225 repeater connected to a 6.6 DB gain antenna. The problem is the system does not work very well. I cannot talk to the repeater outside of 1 - 2 mile radius unless I am on top of another hill. This apparently is due to location as we are surrounded by several hills, and also the elevation of the antenna is not very high. I have it about 25 feet in the air but I do not believe that is enough. My question is how I go about finding information about renting tower space on someone else’s tower. Any information or assistance is greatly appreciated! Thank you!
-Bob
-
- Posts: 1477
- Joined: Sat Nov 29, 2003 10:10 pm
- What radios do you own?: AM/FM
For another thing, a gain antenna when you're in a hilly area is akin to pissing into the wind. Gain antennas merely flatten the RF out, and of course when you're at the bottom of a gulch or a valley you are not doing yourself any favors by flattening the RF right into dirt (RF does not travel well through dirt!).
Getting rid of the gain antenna may help out more than you expect. So might raising your antenna another 25 feet (if possible). Then again, maybe it won't. Without doing a site survey, there is no possible way to know the dynamics of the site, and there are too many variables that affect propagation that you may not even realize exist.
The cost of renting tower space and floor space for your rack will vary. Here in Los Angeles, a rack at a populated mountaintop and a decent spot for your antenna can easily run $1000/month or more. There is no way to say what a "good" price is for your area until you've done some comparison shopping.
I don't know where you live, but like anything else in the world, it's all about supply and demand. If there are many good hilltops in your area with infrastructure ready to go, and not many customers renting space, then you will probably do OK. Few sites and lots of customers can signal a need to get your pocketbook out.
Getting rid of the gain antenna may help out more than you expect. So might raising your antenna another 25 feet (if possible). Then again, maybe it won't. Without doing a site survey, there is no possible way to know the dynamics of the site, and there are too many variables that affect propagation that you may not even realize exist.
The cost of renting tower space and floor space for your rack will vary. Here in Los Angeles, a rack at a populated mountaintop and a decent spot for your antenna can easily run $1000/month or more. There is no way to say what a "good" price is for your area until you've done some comparison shopping.
I don't know where you live, but like anything else in the world, it's all about supply and demand. If there are many good hilltops in your area with infrastructure ready to go, and not many customers renting space, then you will probably do OK. Few sites and lots of customers can signal a need to get your pocketbook out.
- HLA
- Posts: 2334
- Joined: Mon Jul 11, 2005 8:15 pm
- What radios do you own?: HT1550's, X9000's, CDM1550's
if the tip of your antennae is 25 feet in the air you should be getting alot more than 2 miles, you can get 2 miles just direct portable to portable. i'd do some looking around and find the problem with what you have now. is it possible the power is turned down on the repeater or as somebody mentioned earlier, is your duplexer tuned right?
HLA
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
Interesting...
Thank you everyone for your input.
I am not sure I want to pay $1000.00/month for a tower :-/ But I will do some looking around. I fear however this might not be a viable option anymore
HLA/VE3NSV,
I asked myself the same questions you are when I started this and found the performance of the system was very lacking. I am using RG8/U feed line traveling approx 30 feet. As far as the duplexer I knew at one time exactly what model it was but I honestly forgot. I believe it is a knotch type duplexer. It is internal to the repeater. I had the repeater looked at by a service tech. and he stated that it was operating fine. He stated it "was more sensitive than he thought it would be with a duplexer." So apparently the repeater is not the problem but I am still not too sure.
So my next question is what options do I have to boost the performance of this system if I can’t find any good sites that I can actually afford? What else can I do to make sure my system isn’t actually the problem? As always I do appreciate your help. It does help me a lot. Thank you. =)
-Bob
I am not sure I want to pay $1000.00/month for a tower :-/ But I will do some looking around. I fear however this might not be a viable option anymore
HLA/VE3NSV,
I asked myself the same questions you are when I started this and found the performance of the system was very lacking. I am using RG8/U feed line traveling approx 30 feet. As far as the duplexer I knew at one time exactly what model it was but I honestly forgot. I believe it is a knotch type duplexer. It is internal to the repeater. I had the repeater looked at by a service tech. and he stated that it was operating fine. He stated it "was more sensitive than he thought it would be with a duplexer." So apparently the repeater is not the problem but I am still not too sure.
So my next question is what options do I have to boost the performance of this system if I can’t find any good sites that I can actually afford? What else can I do to make sure my system isn’t actually the problem? As always I do appreciate your help. It does help me a lot. Thank you. =)
-Bob
- HLA
- Posts: 2334
- Joined: Mon Jul 11, 2005 8:15 pm
- What radios do you own?: HT1550's, X9000's, CDM1550's
put a meter on it and see how much output you are getting.
HLA
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
I never check PM's so don't bother, just email me.
I won't reply to a hotmail, gmail, aol or any other generic free address, if you want me to reply use a real address.
STOP ASKING ME FOR SOFTWARE OR FIRMWARE, I JUST FORWARD ALL OF THE REQUESTS TO THE MODERATORS
- RESCUE161
- Batboard $upporter
- Posts: 2062
- Joined: Wed Jan 16, 2002 4:00 pm
- What radios do you own?: Too many!
Re: Interesting...
There's a major part of your problem. Get rid of that lossy cable and get some 1/2" Heliax. I had a repeater with an antenna at about 25 feet and I got a least a 7 miles away from it before it started crapping out. It would have been even better coverage, but we were using DES on it.USSZulu2 wrote:I am using RG8/U feed line traveling approx 30 feet.
Scott
KE4FHH
Religion: Kills folks dead!
KE4FHH
Religion: Kills folks dead!
Did the tech do a desens check. Yeah you can still have good sensitivity through a poorly tuned duplexer, and a poorly tuned duplexer can kill coverage. The coax you are using now is not the best, but you stated you were using only 30ft so you have less than 2 db of loss, and thats not too bad, its definitely not your problem. Don't go and spend money on hardline yet. Also have you tried getting another user to sit at the repeater location and see if you can talk mobile to mobile simplex? If you can at ground level then get your repeater double checked. If you can't talk, hook a mobile unit to the repeaters antenna and try that. That will at least point you in a good direction.
-
- Posts: 1477
- Joined: Sat Nov 29, 2003 10:10 pm
- What radios do you own?: AM/FM
agreed. start testing individual parts of the whole, to see what your weak link is.
ard099 says to check your repeater antenna on a separate mobile, i'd also include that to say check your repeater on another antenna, different feed line, check your portables point to point...maybe an alignment....and i would lose the gain antenna in a valley, like escomm said.
ard099 says to check your repeater antenna on a separate mobile, i'd also include that to say check your repeater on another antenna, different feed line, check your portables point to point...maybe an alignment....and i would lose the gain antenna in a valley, like escomm said.
-
- Posts: 236
- Joined: Mon Aug 16, 2004 3:47 pm
I agree that you need to fix your system problems, whatever they are, before you rent some (expensive) site, and find that you STILL need to improve the system.
I formerly had a "quickie" system here locally, an import dual band G6 style monopole 40' up, with about 5 watts output for remote radio control on amateur 440 band. I could easily work it with 5 watts from a handheld 5 miles or so. The tower is in a bit of a depression, too.
You need to actually bribe/hire/get a tech with some test equipment. Measure the loss through your duplexer, your feedline, and the output of the transmitter. Check the SWR into the duplexer, as well as the antenna.
Have someone measure the repeater receiver sensitivity, and check for desense through the duplexer. For all I know the antenna itself may be a stone. Try a different antenna, just for comparison, even if it's a homebrew ground plane 1/4 wave.
I formerly had a "quickie" system here locally, an import dual band G6 style monopole 40' up, with about 5 watts output for remote radio control on amateur 440 band. I could easily work it with 5 watts from a handheld 5 miles or so. The tower is in a bit of a depression, too.
You need to actually bribe/hire/get a tech with some test equipment. Measure the loss through your duplexer, your feedline, and the output of the transmitter. Check the SWR into the duplexer, as well as the antenna.
Have someone measure the repeater receiver sensitivity, and check for desense through the duplexer. For all I know the antenna itself may be a stone. Try a different antenna, just for comparison, even if it's a homebrew ground plane 1/4 wave.
Re: Renting a tower for GMRS Repeater...
If the antenna is truly 6.6 db gain on UHF it would be 9 to 12 feet long.USSZulu2 wrote:Hi Everyone,
repeater connected to a 6.6 DB gain antenna.
-Bob
What is the model and mfgr. info on your "antenna"?
(I know, here we go on antenna gain ,,AGAIN)
<img src="http://www.la.gg/upl/gain.bmp"></img>
-
- Posts: 236
- Joined: Mon Aug 16, 2004 3:47 pm
I made this picture a while back to demonstrate the effects of high antenna gain when you don't really want it. I realize it is crude and exaggerated, but thats why I'm a dispatcher and not an artist.
"I'll eat you like a plate of bacon and eggs in the morning. "
- Some loser on rr.com
eBay at it's finest:
Me: "What exactly is a 900Mhz UHF CB?"
Them: "A very nice CB at 900Mhz speed!"
- Some loser on rr.com
eBay at it's finest:
Me: "What exactly is a 900Mhz UHF CB?"
Them: "A very nice CB at 900Mhz speed!"
That's a nice helpful graphic illustration from nmfire10 . I guess there's greater mystique and hype in antenna marketing than in any other aspect of the profession or hobby so a good illustration is very useful.
One thing I'm not clear on is the relationship of the ground plane surface or the ground plane radials in a base antenna to the overall performance. Does the ground plane figure into the gain formula or the radiation pattern significantly ?
One thing I'm not clear on is the relationship of the ground plane surface or the ground plane radials in a base antenna to the overall performance. Does the ground plane figure into the gain formula or the radiation pattern significantly ?
Thank you everyone for your input! It is very useful
I have decided to reevaluate the components of my system. The tech that looked at my system did NOT check the duplexer. He stated that because of how sensitive the receiver was he did not believe it to be needed. He stated that "it was more sensitive than he expected though the duplexer". This duplexer might be a problem though. Anyways I do have a service monitor, however, I never checked a duplexer with it and I am not sure how to go about it. How do you run a desense check on a duplexer? I would be happy to learn!
As far as the antenna, I am using a Decibel DB-408-B. I see what you mean about too much gain for terrain. My question is does that effect received signal or just transmitted signal? I was always under the impression high gain antennas allow to pick up very weak signals. That was what was explained to me by several techs. The problem I am having is mainly the repeater cannot hear me. What would be some good antenna alternatives?
The feed line I agree isn’t the best...however as stated before it is only 30 feet. This probably will be the last component I attempt to repair/replace. From what I understand that type of line can be VERY expensive. I need to verify for sure that is the problem.
I am going to do the recommended checks with simplex and other radios connected to the antenna. If anyone has any other suggestions or if I might have forgotten to comment on your suggestion please tell me. I do appreciate all the assistance everyone is giving me. It’s overwhelming in a good way! =)
-Bob
I have decided to reevaluate the components of my system. The tech that looked at my system did NOT check the duplexer. He stated that because of how sensitive the receiver was he did not believe it to be needed. He stated that "it was more sensitive than he expected though the duplexer". This duplexer might be a problem though. Anyways I do have a service monitor, however, I never checked a duplexer with it and I am not sure how to go about it. How do you run a desense check on a duplexer? I would be happy to learn!
As far as the antenna, I am using a Decibel DB-408-B. I see what you mean about too much gain for terrain. My question is does that effect received signal or just transmitted signal? I was always under the impression high gain antennas allow to pick up very weak signals. That was what was explained to me by several techs. The problem I am having is mainly the repeater cannot hear me. What would be some good antenna alternatives?
The feed line I agree isn’t the best...however as stated before it is only 30 feet. This probably will be the last component I attempt to repair/replace. From what I understand that type of line can be VERY expensive. I need to verify for sure that is the problem.
I am going to do the recommended checks with simplex and other radios connected to the antenna. If anyone has any other suggestions or if I might have forgotten to comment on your suggestion please tell me. I do appreciate all the assistance everyone is giving me. It’s overwhelming in a good way! =)
-Bob
-
- Posts: 423
- Joined: Thu Aug 24, 2006 11:23 am
- What radios do you own?: Centracom Gold Elite, XTS5K 4K
Well 30ft of 1/2in heliax will only cost you $45, from tessco gold pricing its $1.50 a foot.
If you dont have gold pricing... refer to this post
http://batboard.batlabs.com/viewtopic.php?t=66892
If you dont have gold pricing... refer to this post
http://batboard.batlabs.com/viewtopic.php?t=66892
-Jon
-
- Posts: 44
- Joined: Mon Apr 10, 2006 1:11 pm
- What radios do you own?: Too Many to list
Ok, for the service monitor, it needs to have a spectrum analyser and tracking generator( their are several posts/threads on this board on how to tune a duplexer, but if you have never tuned one, I dont recomond trying to do it. but I can try to walk you through if need be...) PM me if you need help and we can exchange phone numbers
HW
HW
If all you have is a service monitor,here is a crude test for desense:
Put a telescoping antenna on your generate port of the monitor,generate a signal with no pl/dpl till you hear it on the receiving radio,key up the transmitter with a local mic,if the rec goes deaf,you have desense.
Yes there are many better ways than this,but it will tell you something!
mod
Put a telescoping antenna on your generate port of the monitor,generate a signal with no pl/dpl till you hear it on the receiving radio,key up the transmitter with a local mic,if the rec goes deaf,you have desense.
Yes there are many better ways than this,but it will tell you something!
mod
-
- Posts: 236
- Joined: Mon Aug 16, 2004 3:47 pm
A piece on desense:
http://www.ak2o.org/srg/Desense_testing.html
More light reading from the same page:
http://www.ak2o.org/srg/tech.html
and more yet, an exellant page, by the way:
http://www.repeater-builder.com/rbtip/techindex.html
http://www.ak2o.org/srg/Desense_testing.html
More light reading from the same page:
http://www.ak2o.org/srg/tech.html
and more yet, an exellant page, by the way:
http://www.repeater-builder.com/rbtip/techindex.html