Spectra Consolette Accessory Pinouts Needed. Thanks

[USGOVTECH]

I need the pinouts for a Motorola Spectra Consolette. The Accessory 1 and Accessory 2 plugs. Thanks

[misawatech]

I have a pdf file showing the pinouts for the spectra base stations. If someone could tell me how to get it posted in model specific info I would be happy to provide the file or scan the manuals and provide a doc file.

usgovtech...If you provide me an email addess, via pm, I can send the file to you now.

[Bruce1807]

J2

Pin Signal Name Description
1 RX+ (LINE1+)† Receive high used with TRC desksets (TX and RX high for two-wire operation; RX high for four-wire operation)†
2 AUD_SHLD Ground: audio or analog
3 TX+ (LINE2+)† Transmit high used with all desksets (TX high for four-wire operation)†
4 FILT_AUD (DET_AUD)† RX filtered audio (RX detect or discriminator audio)†
5 A+ +13.8VDC or battery voltage
6 BUSY Busy line of data bus; 5V logic
7 BUS+ High side of bus data: 180° out of phase with BUS–; 5V logic
8 UNAVAILABLE Not supported
9 VIP OUTPUT 1 Vehicle interface output port 1
10 PTT* Push-To-Talk initiates a transmission; 5V logic
11 TX– (LINE2–)† Transmit low use with all desksets (TX low for four-wire operation)†
12 DIG_GND Ground for 5V logic signals
13 VIP INPUT 1 Vehicle interface input port 1
14 REMOTE_RX+ (SPKR_HI)† Remote deskset speaker high output (CAUTION: grounding this pin will result in damage to the radio) (Speaker high output)†
15 REMOTE_RX– (SPKR_LO)† Remote deskset speaker low output (CAUTION: grounding this pin will result in damage to the radio) (Speaker low output)†
16 RX– (LINE1–)† Receive low used with TRC desksets (TX and RX low for two-wire operation, RX low for four-wire operation)†
17 TX_AUD (AUD_TX)† Transmit audio used for telephone interconnect
18 VIP OUTPUT 3 Vehicle interface output port 3
19 BUS– Low side of bus data: 180° out of phase with BUS–; 5V logic
20 RESET Data bus reset line; 5V logic
21 5V 5V for logic circuits
22 VIP INPUT 3 Vehicle interface input port 3
23 VIP OUTPUT 2 Vehicle interface output port 2
24 MONITOR* Allows activation of monitor (used with MRTI telephone interconnect)
25 SPKR_UNMUTE Signal indicating if the Consolette is receiving valid audio


J3
Pin Signal Name Description
1 RS232_RXD (NC)† RS232 receive data (pin not used on TRC)†
2 ANA_GND Ground: audio or analog
3 AUX_RX_AUD External SECURENET not supported by the Consolette
4 FILT_AUD (DET_AUD)† RX filtered audio (RX detect or discriminator audio)†
5 A+ +13.8 Vdc or battery voltage
6 BUSY Busy line of data bus; 5V logic
7 BUS+ High side of bus data: 180° out of phase with BUS–; 5V logic
8 BUS_SHLD Ground for data bus; logic ground
9 VSENSE1 (RS232_RXD)† External SECURENET not supported by the Consolette (RS232 receive data)
10 VSENSE1_SHLD Ground for VSENSE; analog ground
11 TAPE_OUT Tape recorder audio output
12 DIG_GND Ground for 5V logic signals
13 EMER Activates emergency MDC1200 transmission
14 RS232_TXD (NC)† RS232 transmit data (pin not used on TRC)†
15 RS232_RTS (NC)† RS232 request to send (pin not used on TRC)†
16 RS232_CTS (PS_AUD_OUT)† RS232 clear to send (external SECURENET not supported by the Consolette)†
17 AUX_TX_AUD External SECURENET not supported by the Consolette
18 SWB+ Switched +13.8 Vdc or battery voltage
19 BUS– Low side of bus data: 180° out of phase with BUS–; 5V logic
20 RESET Data bus reset line; 5V logic
21 NC Currently not used
22 NC (RS232_TXD)† Pin not used on AIB (RS232 Transmit data)†
23 VSENSE2 (RS232_RTS)† External SECURENET not supported by the Consolette (RS232 request to send)†
24 VSENSE2_SHLD Ground for VSENSE; analog ground
25 NC (RS232_CTS)† Pin not used on AIB (RS232 clear to send)†

[USGOVTECH]

Thanks a lot!!!

[dsheli]

Hey guys,
We have an astro spectra consolette that we would like to connect to a computer via the computers sound card Mic input. Does anyone know off the top of their head which pins I should use. I just don't want to use a powered port and blow my sound card.

Thanks,
Dsheli

[Wadsworth]

I am also searching for a pin-out for a Consolette Accessory 1 RJ-45 jack. If anyone can direct me, it isn't in the manual I have.

Thanks!