msf5000 HSO mod?
Moderator: Queue Moderator
-
- Posts: 34
- Joined: Tue Jun 07, 2005 6:22 pm
msf5000 HSO mod?
greetings all.......
i have an msf-5000 analog repeater on 900, but is missing the hi stability osc module.... i heard there is a work around where the HSO module is not needed....... anyone have any details?
tnx,
joe ki8hp
i have an msf-5000 analog repeater on 900, but is missing the hi stability osc module.... i heard there is a work around where the HSO module is not needed....... anyone have any details?
tnx,
joe ki8hp
Re: msf5000 HSO mod?
I think you can cable several of them together to share an HSO. That probably doesn't help you, but it does explain why they're usually missing. Another reference oscillator could probably be cabled in instead, perhaps from a GPS receiver.
'JK
'JK
-
- Batboard $upporter
- Posts: 459
- Joined: Sun Sep 16, 2001 4:00 pm
Re: msf5000 HSO mod?
I have a spare HSO from a Purc5K. If you are interested, drop me an email and we can work something out.
Re: msf5000 HSO mod?
Will - if the original poster does not respond or declines please pm me as I am interested in an HSO as well.
tnx.....dan n2aym
tnx.....dan n2aym
fineshot1
NJ USA
NJ USA
- MSS-Dave
- Posts: 770
- Joined: Mon Jun 30, 2003 6:02 pm
- What radios do you own?: Harris XL200M. XPR7550E, NX300
Re: msf5000 HSO mod?
Just some info...
Every MSF 5K 900 MHz TRUNKED station I've come across did not have the actual 5MHz reference built in. Moto sites used a master Rubidium standard outputting 5Mhz to lock all of the stations to a common source since the freq error requirement is so tight at 900. Forgive me for not having part numbers here but these stations have the tray in the bottom of the cabinet that accepts the 5 MHz to phase lock a 14.4 MHz synthesizer that ultimately drives the station. You should have this tray in the station unless someone pulled it. Then you want a complete tray like Will has, the Purc used the same setup. If you can't come up with 5 MHz externally or the internal standard for the tray, the board is jumper selectable to use several frequencies like 100 KHz, 5 and 10 MHz. I have to look at my spare or the book to see some of the other freqs available. I've never tried to run any of these units at any thing but 5 Mhz since I had that available. Just letting you know there are a couple of options to explore if you want. The UHF station does the 14.4 MHz freq, it's intregrated on the UNiboard. I don't remember if the uniboard on the 900 stations could accept a 14.4 oscillator. Perhaps xmo or Bernie can weigh in if they have experimented with this...
Every MSF 5K 900 MHz TRUNKED station I've come across did not have the actual 5MHz reference built in. Moto sites used a master Rubidium standard outputting 5Mhz to lock all of the stations to a common source since the freq error requirement is so tight at 900. Forgive me for not having part numbers here but these stations have the tray in the bottom of the cabinet that accepts the 5 MHz to phase lock a 14.4 MHz synthesizer that ultimately drives the station. You should have this tray in the station unless someone pulled it. Then you want a complete tray like Will has, the Purc used the same setup. If you can't come up with 5 MHz externally or the internal standard for the tray, the board is jumper selectable to use several frequencies like 100 KHz, 5 and 10 MHz. I have to look at my spare or the book to see some of the other freqs available. I've never tried to run any of these units at any thing but 5 Mhz since I had that available. Just letting you know there are a couple of options to explore if you want. The UHF station does the 14.4 MHz freq, it's intregrated on the UNiboard. I don't remember if the uniboard on the 900 stations could accept a 14.4 oscillator. Perhaps xmo or Bernie can weigh in if they have experimented with this...
-
- Batboard $upporter
- Posts: 459
- Joined: Sun Sep 16, 2001 4:00 pm
Re: msf5000 HSO mod?
Dave, if you could look up the jumper settings for some of the other frequencies, I, and a lot of other people, would be eternally grateful.....
Will
Will
- MSS-Dave
- Posts: 770
- Joined: Mon Jun 30, 2003 6:02 pm
- What radios do you own?: Harris XL200M. XPR7550E, NX300
Re: msf5000 HSO mod?
OK then... Dug in the garage and came up with this. The Reference Synthesizer Board is a TLF 6816A. It has a 14.4 MHz VCXO that is phase locked to the HSO which can be 100 KHz, 1 MHz, 5 MHz or 10 MHz. I have only run the stock config of 5 MHz in many sites but I have had 10 stations daisy chained to a single source when I had a failure. Jumper settings are: JU20 OUT, JU21 OUT = 100 KHz. JU20 OUT, JU21 IN = 1 MHz. JU20 IN, JU21 IN = 5 MHz (default) JU20 IN, JU21 OUT = 10 MHz. These jumpers are 0 Ohm resistors. The HSO has to be very stable due to the reference dividers that are in the chain. I've run stations using the output from a service monitor at +5 dBm but I don't think it will lock at 0 or less.willbartlett wrote:Dave, if you could look up the jumper settings for some of the other frequencies, I, and a lot of other people, would be eternally grateful.....
Will
Looking at some of the latest posts, looks like there will be lots of 927 machines going all over the place. Good Luck with it!
BTW... If someone came up with the MSF 5K 900 TRUNKED station manual, the schematic and board descriptions are located in the reference synthesis tab. There should be simular in the PURC 5K book also.
Dave
Re: msf5000 HSO mod?
There is a simple workaround where you supply your own HSO in place of the real Moto HSO module. The repeater HAS to have a 5 MHz (or 10MHz if changing jumpers works) input from SOMEWHERE in order to generate the 14.4MHz reference needed for the station to operate.The Kreick wrote:greetings all.......
i have an msf-5000 analog repeater on 900, but is missing the hi stability osc module.... i heard there is a work around where the HSO module is not needed....... anyone have any details?
tnx,
joe ki8hp
I just recently picked up a MSF5K 900MHz repeater, one of the 150W trunking repeaters that came up to the New England area from the NJ power company upgrade. Batlabs thread: http://batboard.batlabs.com/viewtopic.php?f=3&t=63976
Mine does not have the HSO module and I too am on the hunt for one. Many of the GEMOTO guys in the Boston area have successfully put these repeaters on the air using a Vectron 5MHz OCXO. It's a da@mn good deal at $50:
http://www.alltronics.com/cgi-bin/item/ ... Oscillator
I'm waiting for mine which should arrive in about a week.
The New England 900MHz MSF5K repeater experience:
http://www.repeater-builder.com/motorol ... 0-msf.html
From looking at what people have done with the Vectron 5MHz OCXO, it should be easy to hook it up in place of a real Moto HSO. What I'm wondering about is there's a VCO control input on the Vectron OCXO part and I don't know if it's an enable/disable logic input or a 0 to 5V analog input to warp the 5MHz frequency slightly. There's also an adjustment hole (covered by a screw) to tweak the OCXO if needed.
People that are using the Vectron OCXO 5MHz part in place of a real Moto HSO have reported that it works quite well. Not bad for a $50 workaround!
Good luck.
David Sterrett
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)
Re: msf5000 HSO mod?
I believe the 0-5V VCO input (some are 0-10V) on the 5 MHz Vectron oscillator is a fine-tuning input. If you use it for that purpose, the voltage must be rock-stable and well-filtered. Of course it could also be used as a modulation input, but I don't know how fast the VCO will respond to changes. Some people just connect that line to +5V, others ignore it. You can still adjust the coil behind the big screw to get the oscillator within 0.1 Hz.
There are also a couple of MSF Experience articles on http://www.repeater-builder.com, in the Motorola section, MSF&PURC area, but since nobody on this board reads stuff on repeater-builder.....
Bob M.
There are also a couple of MSF Experience articles on http://www.repeater-builder.com, in the Motorola section, MSF&PURC area, but since nobody on this board reads stuff on repeater-builder.....
Bob M.
-
- Posts: 77
- Joined: Wed Apr 05, 2006 1:09 pm
- What radios do you own?: xts3000/2500/mcs2000/mts2000
Re: msf5000 HSO mod?
You do not necessarily need either an HSO or a Vectron 5 MHZ OCXO. Ken Campbell, WG1U, has developed a couple of mods for putting a 900 MHZ MSF5000 on the air without a 5 MHZ reference. You can check out photo's taken by N1IIC at Boxboro last month. These mods were introduced by Ken at the 902 seminar given at the convention. We currently have two MSF's on the air with his Maxtrac mod (very stable in conventional repeater operation). My MSF in Plymouth is on the air with his jumper wire mod. The following link will take you to some of the pictures:
http://www.flickr.com/photos/jasongreene/page4/
Ken has added comments to some of the pictures. He has also corrected some info on the maxtrac mod and the corrections are included in his comments.
His jumper mod is the simplest, but it seems to be temperature sensitive. That is not a problem for my repeater as it is located in a temperature regulated room at a commercial site. Ken offers some suggestions for trying this mod when temps are not very stable. His Maxtrac mod, currently running on the Taunton repeater and the W1WCF Bridgewater repeater, is VERY stable.
John
N1OTY
http://www.flickr.com/photos/jasongreene/page4/
Ken has added comments to some of the pictures. He has also corrected some info on the maxtrac mod and the corrections are included in his comments.
His jumper mod is the simplest, but it seems to be temperature sensitive. That is not a problem for my repeater as it is located in a temperature regulated room at a commercial site. Ken offers some suggestions for trying this mod when temps are not very stable. His Maxtrac mod, currently running on the Taunton repeater and the W1WCF Bridgewater repeater, is VERY stable.
John
N1OTY
Re: msf5000 HSO mod?
Hi John,
I was at that seminar (900MHz) at Boxboro! I remember the jumper wire mod mentioned. My g/f was also with me. What clicked with her during the talk about how hams got their radios was with how commercial radios are programmed (via PC & software, etc.). She's seen me do that enough times over the years. It makes a lot more sense to her now. Now all she needs to do is get her ham license.
I think I'm gonna stick with Vectron 5MHz osc since I'm already headed well down that path plus I want it stable with temperature and don't want to ever worry about it once the repeater goes into service.
73,
Dave/N1DAS
I was at that seminar (900MHz) at Boxboro! I remember the jumper wire mod mentioned. My g/f was also with me. What clicked with her during the talk about how hams got their radios was with how commercial radios are programmed (via PC & software, etc.). She's seen me do that enough times over the years. It makes a lot more sense to her now. Now all she needs to do is get her ham license.
I think I'm gonna stick with Vectron 5MHz osc since I'm already headed well down that path plus I want it stable with temperature and don't want to ever worry about it once the repeater goes into service.
73,
Dave/N1DAS
David Sterrett
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)
-
- Posts: 77
- Joined: Wed Apr 05, 2006 1:09 pm
- What radios do you own?: xts3000/2500/mcs2000/mts2000
Re: msf5000 HSO mod?
Interestingly, we have found the maxtrac mod is more stable than the 5 mhz Vectron oscillator. YMMV. Apparently, there is nothing magical about using a 5 mhz reference, since Motorola allows these repeaters to be jumpered for 100 khz, 1 mhz, 5 mhz and 10 mhz references.
John
N1OTY
John
N1OTY
Re: msf5000 HSO mod?
HMMM....interesting! I'll have to look into the maxtrac mod. It's good that we have several options available for providing a stable reference.n1oty wrote:Interestingly, we have found the maxtrac mod is more stable than the 5 mhz Vectron oscillator. YMMV. Apparently, there is nothing magical about using a 5 mhz reference, since Motorola allows these repeaters to be jumpered for 100 khz, 1 mhz, 5 mhz and 10 mhz references.
John
N1OTY
David Sterrett
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)
Nashua, NH
Ham [HA] = N1DAS (2/1984)
GMRS [ZA] = KAE9013 (12/1992)