HMN4079D Programming Issue
Moderator: Queue Moderator
HMN4079D Programming Issue
HNM4079D on XTL5000 O5 Control Head
Model M20QSS9PW1AN
Flash: 580208-001C80-9
Firmware 12
CPS 12
When I try to program the three side buttons, the radio ignores what I program:
Upper/No-dot program as Scan gives me Unpr
Middle/1-dot program as ZnDn gives me Unpr
Bottom/2-dot program as ZnUp gives me Unpr
No matter what combinations I try, it does not take. Sometimes the Upper and Middle keys program but not correctly. The bottom 2-dot key never programs. I have tried programming the Trunk Side the same as the Conventional Side and also leaving the Trunk Side unprogrammed. The radio is used for Conventional only.
Do I have to tell the radio that there is an HNM4079 attached? How?
Okay, I'm confused.
Marshall
Model M20QSS9PW1AN
Flash: 580208-001C80-9
Firmware 12
CPS 12
When I try to program the three side buttons, the radio ignores what I program:
Upper/No-dot program as Scan gives me Unpr
Middle/1-dot program as ZnDn gives me Unpr
Bottom/2-dot program as ZnUp gives me Unpr
No matter what combinations I try, it does not take. Sometimes the Upper and Middle keys program but not correctly. The bottom 2-dot key never programs. I have tried programming the Trunk Side the same as the Conventional Side and also leaving the Trunk Side unprogrammed. The radio is used for Conventional only.
Do I have to tell the radio that there is an HNM4079 attached? How?
Okay, I'm confused.
Marshall
Re: HMN4079D Programming Issue
Do you have those functions as menu items?
Re: HMN4079D Programming Issue
Yes I have SCAN and ZONE set as menu items.
Marshall
Marshall
Re: HMN4079D Programming Issue
Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
-Marc
-Marc
Stupidity creates job security!
If your radio has old firmware, programming it with the latest CPS will not add any new features unless you have the latest firmware to match..
CPS = Customer Programming Software, Not CPS Software.
If your radio has old firmware, programming it with the latest CPS will not add any new features unless you have the latest firmware to match..
CPS = Customer Programming Software, Not CPS Software.
Re: HMN4079D Programming Issue
Mfire39 wrote:Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
But there are on the hmn4079 mic. /\/\
-Marc
Re: HMN4079D Programming Issue
I suspect if you take them out as menu items for the soft keys on the head that they will start working on the DTMF mic.rc50won wrote:Yes I have SCAN and ZONE set as menu items.
Marshall
Re: HMN4079D Programming Issue
I changed the codeplug and will download it in the morning. Thanks for the help.
Marshall
Marshall
escomm wrote:I suspect if you take them out as menu items for the soft keys on the head that they will start working on the DTMF mic.rc50won wrote:Yes I have SCAN and ZONE set as menu items.
Marshall
Re: HMN4079D Programming Issue
You're right, I was having a little mental moment over here..rc50won wrote:Mfire39 wrote:Do you mean you have an 03 head and not an 05? There are no side buttons on an 05 head...
But there are on the hmn4079 mic. /\/\
-Marc
-Marc
Stupidity creates job security!
If your radio has old firmware, programming it with the latest CPS will not add any new features unless you have the latest firmware to match..
CPS = Customer Programming Software, Not CPS Software.
If your radio has old firmware, programming it with the latest CPS will not add any new features unless you have the latest firmware to match..
CPS = Customer Programming Software, Not CPS Software.
Re: HMN4079D Programming Issue
Taking the duplicate commands out of the O5 head menu did not work.
I am seeing a pattern though. Whatever I program into the Upper/No-Dot button winds up being programmed into the O5 Head Red button. Items programmed into the 1 and 2 Dot buttons move up to the No-Dot and 1-Dot buttons and the 2-Dot button is blank. I can repeat this pattern with different commands.
At this point I am guessing that either I have a bad codeplug or I just discovered a firmware issue.
Marshall
I am seeing a pattern though. Whatever I program into the Upper/No-Dot button winds up being programmed into the O5 Head Red button. Items programmed into the 1 and 2 Dot buttons move up to the No-Dot and 1-Dot buttons and the 2-Dot button is blank. I can repeat this pattern with different commands.
At this point I am guessing that either I have a bad codeplug or I just discovered a firmware issue.
Marshall
- MotoFAN
- Posts: 1054
- Joined: Thu Jun 28, 2007 6:46 am
- What radios do you own?: Approx. 50: Moto & Kenwood
Re: HMN4079D Programming Issue
Guys,
Few questions about HMN4079D:
1. Any way to reprogram some of 4 top front buttons?
2. How to choose menu items from this mic? I am able to navigate through menu by navipad on mic, but I have no ideas how to select/press exact item.
P.S.
3 side buttons already programmed, but it's not enough for me.
Few questions about HMN4079D:
1. Any way to reprogram some of 4 top front buttons?
2. How to choose menu items from this mic? I am able to navigate through menu by navipad on mic, but I have no ideas how to select/press exact item.
P.S.
3 side buttons already programmed, but it's not enough for me.
I am biggest fan of XTS2500 and ASTRO Digital Saber.